PIC12C671-04I/P Microchip Technology Inc., PIC12C671-04I/P Datasheet - Page 66
![no-image](/images/manufacturer_photos/0/4/440/microchip_technology_inc__sml.jpg)
PIC12C671-04I/P
Manufacturer Part Number
PIC12C671-04I/P
Description
8 PIN, 1.75 KB OTP, 128 RAM, 6 I/O
Manufacturer
Microchip Technology Inc.
Datasheet
1.PIC12C671-04IP.pdf
(129 pages)
Specifications of PIC12C671-04I/P
A/d Inputs
4-Channel, 8-Bit
Cpu Speed
2.5 MIPS
Eeprom Memory
0 Bytes
Input Output
5
Memory Type
OTP
Number Of Bits
8
Package Type
8-pin PDIP
Programmable Memory
1.75K Bytes
Ram Size
128 Bytes
Speed
4 MHz
Timers
1-8-bit
Voltage, Range
2.5-5.5 V
Lead Free Status / Rohs Status
RoHS Compliant part
Electrostatic Device
PIC12C67X
9.8
Power-down mode is entered by executing a SLEEP
instruction.
If enabled, the Watchdog Timer will be cleared but
keeps running, the PD bit (STATUS<3>) is cleared, the
TO (STATUS<4>) bit is set, and the oscillator driver is
turned off. The I/O ports maintain the status they had,
before the SLEEP instruction was executed (driving
high, low or hi-impedance).
For lowest current consumption in this mode, place all
I/O pins at either V
cuitry is drawing current from the I/O pin, power-down
the A/D, and disable external clocks. Pull all I/O pins
that are hi-impedance inputs, high or low externally, to
avoid switching currents caused by floating inputs. The
T0CKI input, if enabled, should also be at V
for lowest current consumption. The contribution from
on-chip pull-ups on GPIO should be considered.
The MCLR pin, if enabled, must be at a logic high level
(V
9.8.1
The device can wake-up from SLEEP through one of
the following events:
1.
2.
3.
External MCLR Reset will cause a device reset. All
other events are considered a continuation of program
execution and cause a "wake-up". The TO and PD bits
in the STATUS register can be used to determine the
cause of device reset. The PD bit, which is set on
power-up, is cleared when SLEEP is invoked. The TO
bit is cleared if a WDT time-out occurred (and caused
wake-up).
The following peripheral interrupt can wake the device
from SLEEP:
1.
DS30561B-page 66
IHMC
External reset input on MCLR pin.
Watchdog Timer Wake-up (if WDT was
enabled).
GP2/INT interrupt, interrupt GPIO port change
or some Peripheral Interrupts.
A/D conversion (when A/D clock source is RC).
).
Power-down Mode (SLEEP)
WAKE-UP FROM SLEEP
DD
or V
SS
, ensure no external cir-
DD
or V
SS
Other peripherals can not generate interrupts since
during SLEEP, no on-chip Q clocks are present.
When the SLEEP instruction is being executed, the next
instruction (PC + 1) is pre-fetched. For the device to
wake-up through an interrupt event, the corresponding
interrupt enable bit must be set (enabled). Wake-up is
regardless of the state of the GIE bit. If the GIE bit is
clear (disabled), the device continues execution at the
instruction after the SLEEP instruction. If the GIE bit is
set (enabled), the device executes the instruction after
the SLEEP instruction and then branches to the inter-
rupt address (0004h). In cases where the execution of
the instruction following SLEEP is not desirable, the
user should have a NOP after the SLEEP instruction.
9.8.2
When global interrupts are disabled (GIE cleared) and
any interrupt source has both its interrupt enable bit
and interrupt flag bit set, one of the following will occur:
• If the interrupt occurs before the the execution of
• If the interrupt occurs during or after the execu-
Even if the flag bits were checked before executing a
SLEEP instruction, it may be possible for flag bits to
become set before the SLEEP instruction completes. To
determine whether a SLEEP instruction executed, test
the PD bit. If the PD bit is set, the SLEEP instruction
was executed as a NOP.
To ensure that the WDT is cleared, a CLRWDT instruc-
tion should be executed before a SLEEP instruction.
a SLEEP instruction, the SLEEP instruction will
complete as a NOP. Therefore, the WDT and WDT
postscaler will not be cleared, the TO bit will not
be set and PD bits will not be cleared.
tion of a SLEEP instruction, the device will imme-
diately wake-up from sleep . The SLEEP
instruction will be completely executed before the
wake-up. Therefore, the WDT and WDT
postscaler will be cleared, the TO bit will be set
and the PD bit will be cleared.
WAKE-UP USING INTERRUPTS
1999 Microchip Technology Inc.