PIC24FJ64GA306-I/MR Microchip Technology, PIC24FJ64GA306-I/MR Datasheet - Page 226

• Manufacturer Part Number: PIC24FJ64GA306-I/MR
• Description: 16-bit, 16 MIPS, 64 KB Flash, 8 KB RAM, 53 I/O, LCD, XLP W/Vbat 64 QFN 9x9x0.9mm
• Manufacturer: Microchip Technology

PIC24FJ128GA310 FAMILY
REGISTER 16-2:
DS39996F-page 226
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15-13
bit 12
bit 11
bit 10
bit 9
bit 8
bit 7
bit 6
bit 5
Note 1:
SSEN
R/W-0
U-0
—
2:
3:
4:
(4)
If DISSCK = 0, SCKx must be configured to an available RPn pin. See
Select (PPS)”
If DISSDO = 0, SDOx must be configured to an available RPn pin. See
Select (PPS)”
The CKE bit is not used in the Framed SPI modes. The user should program this bit to ‘0’ for the Framed
SPI modes (FRMEN = 1).
If SSEN = 1, SSx must be configured to an available RPn/PRIn pin. See
Select (PPS)”
Unimplemented: Read as ‘0’
DISSCK: Disable SCKx Pin bit (SPI Master modes only)
1 = Internal SPI clock is disabled; pin functions as I/O
0 = Internal SPI clock is enabled
DISSDO: Disable SDOx Pin bit
1 = SDOx pin is not used by the module; pin functions as I/O
0 = SDOx pin is controlled by the module
MODE16: Word/Byte Communication Select bit
1 = Communication is word-wide (16 bits)
0 = Communication is byte-wide (8 bits)
SMP: SPIx Data Input Sample Phase bit
Master mode:
1 = Input data is sampled at the end of data output time
0 = Input data is sampled at the middle of data output time
Slave mode:
SMP must be cleared when SPIx is used in Slave mode.
CKE: SPIx Clock Edge Select bit
1 = Serial output data changes on transition from active clock state to Idle clock state (see bit 6)
0 = Serial output data changes on transition from Idle clock state to active clock state (see bit 6)
SSEN: Slave Select Enable (Slave mode) bit
1 = SSx pin is used for Slave mode
0 = SSx pin is not used by the module; pin is controlled by the port function
CKP: Clock Polarity Select bit
1 = Idle state for the clock is a high level; active state is a low level
0 = Idle state for the clock is a low level; active state is a high level
MSTEN: Master Mode Enable bit
1 = Master mode
0 = Slave mode
R/W-0
CKP
U-0
—
SPI
X
for more information.
for more information.
for more information.
CON1: SPIx CONTROL REGISTER 1
W = Writable bit
‘1’ = Bit is set
MSTEN
R/W-0
U-0
—
DISSCK
(2)
SPRE2
R/W-0
R/W-0
(3)
(1)
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
(4)
DISSDO
SPRE1
R/W-0
R/W-0
(2)
(1)
MODE16
SPRE0
R/W-0
R/W-0
 2010-2011 Microchip Technology Inc.
Section 11.4 “Peripheral Pin
Section 11.4 “Peripheral Pin
Section 11.4 “Peripheral Pin
x = Bit is unknown
PPRE1
R/W-0
R/W-0
SMP
PPRE0
CKE
R/W-0
R/W-0
(3)
bit 8
bit 0