PIC24FJ64GA306-I/MR Microchip Technology, PIC24FJ64GA306-I/MR Datasheet - Page 165

• Manufacturer Part Number: PIC24FJ64GA306-I/MR
• Description: 16-bit, 16 MIPS, 64 KB Flash, 8 KB RAM, 53 I/O, LCD, XLP W/Vbat 64 QFN 9x9x0.9mm
• Manufacturer: Microchip Technology

10.6
In Run and Idle modes, all PIC24FJ devices allow for a
wide range of clock frequencies to be selected under
application control. If the system clock configuration is
not
high-precision oscillators by simply changing the NOSC
bits. The process of changing a system clock during
operation, as well as limitations to the process, are
discussed in more detail in
tion”.
10.7
Generally, changing clock speed and invoking one of
the power-saving modes are the preferred strategies
for reducing power consumption. There may be
circumstances, however, where this is not practical. For
example, it may be necessary for an application to
maintain uninterrupted synchronous communication,
even while it is doing nothing else. Reducing system
clock speed may introduce communication errors,
while
communications completely.
Doze mode is a simple and effective alternative method
to reduce power consumption while the device is still
executing code. In this mode, the system clock
continues to operate from the same source and at the
same speed. Peripheral modules continue to be
clocked at the same speed while the CPU clock speed
is reduced. Synchronization between the two clock
domains is maintained, allowing the peripherals to
access the SFRs while the CPU executes code at a
slower rate.
Doze mode is enabled by setting the DOZEN bit
(CLKDIV<11>). The ratio between peripheral and core
clock speed is determined by the DOZE<2:0> bits
(CLKDIV<14:12>).
configurations, from 1:1 to 1:128, with 1:1 being the
default.
It is also possible to use Doze mode to selectively reduce
power consumption in event driven applications. This
allows clock-sensitive functions, such as synchronous
communications, to continue without interruption while
the CPU Idles, waiting for something to invoke an
interrupt routine. Enabling the automatic return to
full-speed CPU operation on interrupts is enabled by set-
ting the ROI bit (CLKDIV<15>). By default, interrupt
events have no effect on Doze mode operation.
 2010-2011 Microchip Technology Inc.
locked,
using
Clock Frequency and Clock
Switching
Doze Mode
users
a
power-saving
There
can
9.0 “Oscillator Configura-
choose
are
mode
eight
low-power
may
possible
PIC24FJ128GA310 FAMILY
stop
or
10.8
Idle and Doze modes allow users to substantially
reduce power consumption by slowing or stopping the
CPU clock. Even so, peripheral modules still remain
clocked, and thus, consume power. There may be
cases where the application needs what these modes
do not provide: the allocation of power resources to
CPU processing with minimal power consumption from
the peripherals.
PIC24F devices address this requirement by allowing
peripheral modules to be selectively disabled, reducing
or eliminating their power consumption. This can be
done with two control bits:
• The Peripheral Enable bit, generically named,
• The Peripheral Module Disable (PMD) bit,
Both bits have similar functions in enabling or disabling
its associated module. Setting the PMD bit for a module
disables all clock sources to that module, reducing its
power consumption to an absolute minimum. In this
state, the control and status registers associated with
the peripheral will also be disabled, so writes to those
registers will have no effect and read values will be
invalid. Many peripheral modules have a corresponding
PMD bit.
In contrast, disabling a module by clearing its XXXEN
bit disables its functionality, but leaves its registers
available to be read and written to. Power consumption
is reduced, but not by as much as the PMD bits are
used. Most peripheral modules have an enable bit;
exceptions include capture, compare and RTCC.
To achieve more selective power savings, peripheral
modules can also be selectively disabled when the
device enters Idle mode. This is done through the control
bit of the generic name format, “XXXIDL”. By default, all
modules that can operate during Idle mode will do so.
Using the disable on Idle feature disables the module
while in Idle mode, allowing further reduction of power
consumption during Idle mode, enhancing power
savings for extremely critical power applications.
“XXXEN”, located in the module’s main control
SFR.
generically named, “XXXMD”, located in one of
the PMD Control registers (XXXMD bits are in
PMD1, PMD2, PMD3, PMD4, PMD6, PMD7
registers).
Selective Peripheral Module
Control
DS39996F-page 165