CS8900A-IQ3ZR Cirrus Logic Inc, CS8900A-IQ3ZR Datasheet - Page 39
![no-image](/images/manufacturer_photos/0/1/141/cirrus_logic_inc_sml.jpg)
CS8900A-IQ3ZR
Manufacturer Part Number
CS8900A-IQ3ZR
Description
Ethernet ICs IC 10Mbps Ethernet Controller 3.3V
Manufacturer
Cirrus Logic Inc
Datasheet
1.CS8900A-CQZ.pdf
(138 pages)
Specifications of CS8900A-IQ3ZR
Ethernet Connection Type
10Base- 2, 10Base- 5, 10Base- F, 10Base- T
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Product
Ethernet Controllers
Standard Supported
IEEE 802.3
Data Rate
10 Mbps
Maximum Operating Temperature
+ 85 C
Package / Case
LQFP-100
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CS8900A-IQ3ZR
Manufacturer:
Cirrus Logic Inc
Quantity:
10 000
DS271F5
at least four frames in a row with negative po-
larity after the EOF, the receive pair is consid-
ered reversed. Any data received before the
correction of the reversal is ignored.
3.11.6 Collision Detection
If half-duplex operation is selected (Register
19, Bit E, FDX), the CS8900A detects a
10BASE-T collision whenever the receiver and
transmitter are active simultaneously. When a
collision is present, the Collision Detection cir-
cuit informs the MAC by asserting the internal
Collision signal (see Section 3.9 on page 29
for collision handling).
3.12 Attachment Unit Interface (AUI)
The CS8900A Attachment Unit Interface (AUI)
provides
10BASE2, 10BASE5, and 10BASE-FL Ether-
net transceivers. It is fully compliant with Sec-
tion 7 of the Ethernet standard (ISO/IEC 8802-
3), and as such, is capable of driving a full 50-
meter AUI cable.
The AUI consists of three pairs of signals: Data
Out (DO+/DO-), Data In (DI+/DI-), and Colli-
sion In (CI+/CI-). To select the AUI, the host
should set the AUI bit (Register 13, LineCTL,
Bit 8). The AUI can also be selected automati-
cally as described in the previous section
(Section 3.10.4 on page 36). Figure 15 pro-
vides a block diagram of the AUI. (For a con-
nection
page 122).
3.12.1 AUI Transmitter
The AUI transmitter is a differential driver de-
signed to drive a 78 Ω cable. It accepts data
from the ENDEC and transmits it directly on
the DO+/DO- pins. After transmission has
started, the CS8900A expects to see the pack-
et “looped-back” (or echoed) to the receiver,
causing the Carrier Sense signal to be assert-
CS8900A
Crystal LAN™ Ethernet Controller
diagram,
a
direct
see
interface
Section 7.6
CIRRUS LOGIC PRODUCT DATASHEET
to
external
on
ed. This Carrier Sense presence indicates that
the transmit signal is getting through to the
transceiver. If the Carrier Sense signal re-
mains deasserted throughout the transmis-
sion, or if the Carrier Sense signal is
deasserted before the end of the transmission,
there is a Loss-of-Carrier error and the Loss-
of-CRS bit (Register 8, TxEvent, Bit 6) is set.
3.12.2 AUI Receiver
The AUI receiver is a differential pair circuit
that connects directly to the DI+/DI- pins. It is
designed to distinguish between transient
noise pulses and incoming Ethernet packets.
Incoming packets with proper amplitude and
pulse width are passed on to the ENDEC sec-
tion, while unwanted noise is rejected.
3.12.3 Collision Detection
The AUI collision circuit is a differential pair re-
ceiver that detects the presence of collision
signals on the CI+/CI- pins. The collision signal
is generated by an external Ethernet trans-
ceiver whenever a collision is detected on the
Ethernet segment. (Section 7.3.1.2 of ISO/IEC
8802-3, 1993, defines the collision signal as a
10 MHz ± 15% signal with a duty cycle no
worse than 60/40). When a collision is present,
the AUI Collision circuit informs the MAC by
asserting the internal Collision signal.
DO+
CL+
DO-
CL-
DI+
DI-
- +
- +
AUI
Figure 15. AUI
Collision
Detect
AUICol (to MAC)
AUIRX
AUISQL
AUITX
ENDEC
39