CS8900A-IQ3ZR Cirrus Logic Inc, CS8900A-IQ3ZR Datasheet - Page 36
![no-image](/images/manufacturer_photos/0/1/141/cirrus_logic_inc_sml.jpg)
CS8900A-IQ3ZR
Manufacturer Part Number
CS8900A-IQ3ZR
Description
Ethernet ICs IC 10Mbps Ethernet Controller 3.3V
Manufacturer
Cirrus Logic Inc
Datasheet
1.CS8900A-CQZ.pdf
(138 pages)
Specifications of CS8900A-IQ3ZR
Ethernet Connection Type
10Base- 2, 10Base- 5, 10Base- F, 10Base- T
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Product
Ethernet Controllers
Standard Supported
IEEE 802.3
Data Rate
10 Mbps
Maximum Operating Temperature
+ 85 C
Package / Case
LQFP-100
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CS8900A-IQ3ZR
Manufacturer:
Cirrus Logic Inc
Quantity:
10 000
40% and 60%. The specifications for the crys-
tal are described in Section 7.7 on page 122.
The encoded signal is routed to either the
10BASE-T transceiver or AUI, depending on
configuration.
3.10.2 Carrier Detection
The internal Carrier Detection circuit informs
the MAC that valid receive data is present by
asserting the internal Carrier Sense signal as
soon it detects a valid bit pattern (1010b or
0101b for 10BASE-T, and 1b or 0b for AUI).
During normal packet reception, Carrier Sense
remains asserted while the frame is being re-
ceived, and is deasserted 1.3 to 2.3 bit times
after the last low-to-high transition of the End-
of-Frame (EOF) sequence. Whenever the re-
ceiver is idle (no receive activity), Carrier
Sense is deasserted. The CRS bit (Register
14, LineST, Bit E) reports the state of the Car-
rier Sense signal.
3.10.3 Clock and Data Recovery
When the receiver is idle, the phase-lock loop
(PLL) is locked to the internal clock signal. The
assertion of the Carrier Sense signal interrupts
the PLL. When it restarts, it locks on the in-
coming data. The receive clock is then com-
pared to the incoming data at the bit cell center
and any phase difference is corrected. The
PLL remains locked as long as the receiver in-
put signal is valid. Once the PLL has locked on
the incoming data, the ENDEC converts the
Manchester data to NRZ and passes the de-
coded data and the recovered clock to the
MAC for further processing.
3.10.4 Interface Selection
Physical interface selection is determined by
AUIonly bit (Bit 8) and the AutoAUI/10BT (Bit
36
CIRRUS LOGIC PRODUCT DATASHEET
9) in the LineCTL register (Register 13). Table
12 describes the possible configurations.
3.10.4.1 10BASE-T Only
When configured for 10BASE-T only opera-
tion, the 10BASE-T transceiver and its inter-
face to the ENDEC are active, and the AUI is
powered down.
3.10.4.2 AUI Only
When configured for AUI-only operation, the
AUI and its interface to the ENDEC are active,
and the 10BASE-T transceiver is powered
down.
3.10.4.3 Auto-Select
In Auto-Select mode, the CS8900A automati-
cally selects the 10BASE-T interface and pow-
ers down the AUI if valid packets or link pulses
are detected by the 10BASE-T receiver. If val-
id packets and link pulses are not detected, the
CS8900A selects the AUI. Whenever the AUI
is selected, the 10BASE-T receiver remains
active to listen for link pulses or packets. If
10BASE-T activity is detected, the CS8900A
switches back to 10BASE-T.
3.11 10BASE-T Transceiver
The
10BASE-T transceiver that is compliant with
the relevant portions of section 14 of the Ether-
net standard (ISO/IEC 8802-3, 1993). It in-
cludes all analog and digital circuitry needed to
interface the CS8900A directly to a simple iso-
lation
page 121 for a connection diagram). Figure 13
provides a block diagram of the 10BASE-T
transceiver.
AUIonly
(Bit 8)
CS8900A
0
1
0
transformer
Table 12. Interface Selection
Crystal LAN™ Ethernet Controller
AutoAUI/10BT
includes
(Bit 9)
N/A
(see
0
1
Section 7.5
an
10BASE-T Only
Auto-Select
Interface
Physical
AUI Only
CS8900A
integrated
DS271F5
on