CS8900A-IQ3ZR Cirrus Logic Inc, CS8900A-IQ3ZR Datasheet - Page 37
![no-image](/images/manufacturer_photos/0/1/141/cirrus_logic_inc_sml.jpg)
CS8900A-IQ3ZR
Manufacturer Part Number
CS8900A-IQ3ZR
Description
Ethernet ICs IC 10Mbps Ethernet Controller 3.3V
Manufacturer
Cirrus Logic Inc
Datasheet
1.CS8900A-CQZ.pdf
(138 pages)
Specifications of CS8900A-IQ3ZR
Ethernet Connection Type
10Base- 2, 10Base- 5, 10Base- F, 10Base- T
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Product
Ethernet Controllers
Standard Supported
IEEE 802.3
Data Rate
10 Mbps
Maximum Operating Temperature
+ 85 C
Package / Case
LQFP-100
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CS8900A-IQ3ZR
Manufacturer:
Cirrus Logic Inc
Quantity:
10 000
DS271F5
3.11.1 10BASE-T Filters
The CS8900A’s 10BASE-T transceiver in-
cludes integrated low-pass transmit and re-
ceive filters, eliminating the need for external
filters or a filter/transformer hybrid. On-chip fil-
ters are gm/c implementations of fifth-order
Butterworth low-pass filters. Internal tuning cir-
cuits keep the gm/c ratio tightly controlled,
even when large temperature, supply, and IC
process variations occur. The nominal 3 dB
cutoff frequency of the filters is 16 MHz, and
the nominal attenuation at 30 MHz (3rd har-
monic) is -27 dB.
3.11.2 Transmitter
When configured for 10BASE-T operation,
Manchester encoded data from the ENDEC is
fed into the transmitter’s predistortion circuit
where initial wave shaping and preequaliza-
tion is performed. The output of the predistor-
tion circuit is fed into the transmit filter where
final wave shaping occurs and unwanted noise
is removed. The signal then passes to the dif-
ferential driver where it is amplified and driven
out of the TXD+/TXD- pins.
In the absence of transmit packets, the trans-
mitter generates link pulses in accordance
CS8900A
Crystal LAN™ Ethernet Controller
(to MAC)
LinkOK
ENDEC
RXSQL
RX
TX
CIRRUS LOGIC PRODUCT DATASHEET
Figure 13. 10BASE-T Transceiver
Link Pulse
Distortion
Detector
TX Pre-
10BASE-T Transceiver
with section 14.2.1.1. of the Ethernet standard.
Transmitted link pulses are positive pulses,
one bit time wide, typically generated at a rate
of one every 16 ms. The 16 ms timer starts
whenever the transmitter completes an End-
of-Frame (EOF) sequence. Thus, there is a
link pulse 16 ms after an EOF unless there is
another transmitted packet. Figure 14 dia-
grams the operation of the Link Pulse Genera-
tor.
If no link pulses are being received on the re-
ceiver, the 10BASE-T transmitter is internally
forced to an inactive state unless bit DisableLT
in register 19 (Test Control register) is set to
one.
3.11.3 Receiver
The 10BASE-T receive section consists of the
receive filter, squelch circuit, polarity detection
and correction circuit, and link pulse detector.
3.11.3.1 Squelch Circuit
The 10BASE-T squelch circuit determines
when valid data is present on the RXD+/RXD-
pair. Incoming signals passing through the re-
ceive filter are tested by the squelch circuit.
Any signal with amplitude less than the
Filter Tuning
RX Squelch
Comparator
TX Filters
RX
TX Drivers
RX Filters
RXD-
RXD+
TXD-
TXD+
37