SI1000-C-GM Silicon Laboratories Inc, SI1000-C-GM Datasheet - Page 99

• Manufacturer Part Number: SI1000-C-GM
• Description: IC TXRX MCU + EZRADIOPRO
• Manufacturer: Silicon Laboratories Inc

Specifications of SI1000-C-GM

• Package / Case: 42-QFN
• Frequency: 240MHz ~ 960MHz
• Data Rate - Maximum: 256kbps
• Modulation Or Protocol: FSK, GFSK, OOK
• Applications: General Purpose
• Power - Output: 20dBm
• Sensitivity: -121dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 18.5mA
• Current - Transmitting: 85mA
• Data Interface: PCB, Surface Mount
• Memory Size: 64kB Flash, 4kB RAM
• Antenna Connector: PCB, Surface Mount
• Number Of Receivers: 1
• Number Of Transmitters: 1
• Wireless Frequency: 240 MHz to 960 MHz
• Interface Type: UART, SMBus, SPI, PCA
• Output Power: 20 dBm
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 4.1 mA
• Minimum Operating Temperature: - 40 C
• Modulation: FSK, GFSK, OOK
• Protocol Supported: C2, SMBus
• Core: 8051
• Program Memory Type: Flash
• Program Memory Size: 64 KB
• Data Ram Size: 4352 B
• Supply Current (max): 4.1 mA
• Cpu Family: Si100x
• Device Core: 8051
• Device Core Size: 8b
• Frequency (max): 25MHz
• Total Internal Ram Size: 4.25KB
• # I/os (max): 22
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 1.8V
• On-chip Adc: 18-chx10-bit
• Instruction Set Architecture: CISC
• Mounting: Surface Mount
• Pin Count: 42
• Package Type: QFN EP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1881-5

7. Comparators
Si1000/1/2/3/4/5 devices include two on-chip programmable voltage comparators: Comparator 0 (CPT0) is
shown in Figure 7.1; Comparator 1 (CPT1) is shown in Figure 7.2. The two comparators operate identi-
cally, but may differ in their ability to be used as reset or wake-up sources. See the Reset Sources chapter
and the Power Management chapter for details on reset sources and low power mode wake-up sources,
respectively.
The Comparator offers programmable response time and hysteresis, an analog input multiplexer, and two
outputs that are optionally available at the Port pins: a synchronous “latched” output (CP0, CP1), or an
asynchronous “raw” output (CP0A, CP1A). The asynchronous CP0A signal is available even when the
system clock is not active. This allows the Comparator to operate and generate an output when the device
is in some low power modes.
7.1. Comparator Inputs
Each Comparator performs an analog comparison of the voltage levels at its positive (CP0+ or CP1+) and
negative (CP0- or CP1-) input. Both comparators support multiple port pin inputs multiplexed to their posi-
tive and negative comparator inputs using analog input multiplexers. The analog input multiplexers are
completely under software control and configured using SFR registers. See Section “7.6. Comparator0 and
Comparator1 Analog Multiplexers” on page 106 for details on how to select and configure Comparator
inputs.
Important Note About Comparator Inputs: The Port pins selected as Comparator inputs should be con-
figured as analog inputs and skipped by the Crossbar. See the Port I/O chapter for more details on how to
configure Port I/O pins as Analog Inputs. The Comparator may also be used to compare the logic level of
digital signals, however, Port I/O pins configured as digital inputs must be driven to a valid logic state
(HIGH or LOW) to avoid increased power consumption.
Analog Input Multiplexer
Px.x
Px.x
Px.x
Px.x
Figure 7.1. Comparator 0 Functional Block Diagram
CP0HYN1
CP0HYN0
CP0HYP1
CP0HYP0
CP0OUT
CP0RIF
CP0FIF
CP0EN
CP0 +
CP0 -
+
-
Rev. 1.0
VDD
GND
Decision
Reset
CPT0MD
Tree
(ASYNCHRONOUS)
(SYNCHRONIZER)
D
SET
CLR
Q
Q
D
SET
CLR
Q
Q
Si1000/1/2/3/4/5
Rising-edge
CP0
Crossbar
Interrupt
Logic
Falling-edge
Interrupt
CP0
CP0A
CP0
CP0
99