ATMEGA64RZAV-10MU Atmel, ATMEGA64RZAV-10MU Datasheet - Page 50

• Manufacturer Part Number: ATMEGA64RZAV-10MU
• Description: MCU ATMEGA644/AT86RF230 44-QFN
• Manufacturer: Atmel
• Series: ATMEGAr

Specifications of ATMEGA64RZAV-10MU

• Frequency: 2.4GHz
• Modulation Or Protocol: 802.15.4 Zigbee
• Power - Output: 3dBm
• Sensitivity: -101dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Data Interface: PCB, Surface Mount
• Memory Size: 64kB Flash, 2kB EEPROM, 4kB RAM
• Antenna Connector: PCB, Surface Mount
• Package / Case: 44-VFQFN Exposed Pad
• Wireless Frequency: 2.4 GHz
• Interface Type: JTAG, SPI
• Output Power: 3 dBm
• For Use With: ATSTK600-TQFP32 - STK600 SOCKET/ADAPTER 32-TQFP770-1005 - ISP 4PORT FOR ATMEL AVR MCU JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPIATAVRISP2 - PROGRAMMER AVR IN SYSTEMATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEMATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Applications: -
• Data Rate - Maximum: -
• Current - Transmitting: -
• Current - Receiving: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• For Use With/related Products: ATmega64

8.3 Energy Detection (ED)
8.3.1 Overview
8.3.2 Request an ED Measurement
50
AT86RF230
Bit
0x06
Read/Write
Reset value
Bit
0x06
Read/Write
Reset value
Register 0x06 (PHY_RSSI)
The PHY_RSSI register is a multi purpose register to indicate the current received
signal strength (RSSI) and the FCS validity of a received frame.
• Bit 7 – RX_CRC_VALID
This register bit indicates whether a received frame has a valid FCS. The register bit is
updated when issuing the TRX_END interrupt remains valid until the next TRX_END
interrupt caused by a new frame reception.
Table 8-3. RX FCS Result
• Bit [6:5] – Reserved
• Bit [4:0] – RSSI
Refer to section 8.4.4.
The main features for the Energy Detection module are:
• 85 unique energy levels defined
• 1 dB resolution
The receiver Energy Detection measurement is used by a network layer as part of a
channel selection algorithm. It is an estimation of the received signal power within the
bandwidth of an IEEE 802.15.4-2003 channel. No attempt is made to identify or decode
signals on the channel. The ED value is calculated by averaging RSSI values over eight
symbols (128 µs).
There are two ways implemented in the AT86RF230 to initiate an ED measurement:
• Manually, by a write access to register 0x07 (PHY_ED_LEVEL), or
• Automatically, by detecting a valid SFD of an incoming frame.
For manually initiated ED measurement the radio transceiver needs to be in one of the
states RX_ON or BUSY_RX. An automated ED measurement is started, if a SFD field
is detected. A valid SFD detection is signalized by an RX_START interrupt in Basic
Operating Mode.
Register Bit
RX_CRC_VALID
RX_CRC_VALID
R
R
7
0
3
0
Value
0
1
R
R
6
0
2
0
Description
FCS is not valid.
FCS is valid.
Reserved
RSSI
R
R
5
0
1
0
RSSI
R
R
4
0
0
0
5131E-MCU Wireless-02/09
PHY_RSSI
PHY_RSSI