DF2166VTE33 Renesas Electronics America, DF2166VTE33 Datasheet - Page 535
![MCU FLASH 3V 512K 33MHZ 144TQFP](/photos/28/61/286114/144-tqfp_sml.jpg)
DF2166VTE33
Manufacturer Part Number
DF2166VTE33
Description
MCU FLASH 3V 512K 33MHZ 144TQFP
Manufacturer
Renesas Electronics America
Series
H8® H8S/2100r
Datasheet
1.HS2168EPI61H-U.pdf
(876 pages)
Specifications of DF2166VTE33
Core Processor
H8S/2000
Core Size
16-Bit
Speed
33MHz
Connectivity
I²C, IrDA, LPC, SCI, SmartCard
Peripherals
POR, PWM, WDT
Number Of I /o
106
Program Memory Size
512KB (512K x 8)
Program Memory Type
FLASH
Ram Size
40K x 8
Voltage - Supply (vcc/vdd)
3 V ~ 3.6 V
Data Converters
A/D 8x10b; D/A 2x8b
Oscillator Type
External
Operating Temperature
-20°C ~ 75°C
Package / Case
144-TQFP, 144-VQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-
- Current page: 535 of 876
- Download datasheet (5Mb)
• The value of the ICMR register bit counter (BC2 to BC0)
• Generated interrupt sources (interrupt sources transferred to the interrupt controller)
Notes on Initialization:
• Interrupt flags and interrupt sources are not cleared, and so flag clearing measures must be
• Basically, other register flags are not cleared either, and so flag clearing measures must be
• If a flag clearing setting is made during transmission/reception, the IIC module will stop
The value of the BBSY bit cannot be modified directly by this module clear function, but since the
stop condition pin waveform is generated according to the state and release timing of the SCL and
SDA pins, the BBSY bit may be cleared as a result. Similarly, state switching of other bits and
flags may also have an effect.
To prevent problems caused by these factors, the following procedure should be used when
initializing the IIC state.
1. Execute initialization of the internal state according to the ICE bit clearing.
2. Execute a stop condition issuance instruction (write 0 to BBSY and SCP) to clear the BBSY
3. Re-execute initialization of the internal state according to the ICE bit clearing.
4. Initialize (re-set) the IIC registers.
taken as necessary.
taken as necessary.
transmitting/receiving at that point and the SCL and SDA pins will be released. When
transmission/reception is started again, register initialization, etc., must be carried out as
necessary to enable correct communication as a system.
bit to 0, and wait for two transfer rate clock cycles.
Rev. 3.00, 03/04, page 493 of 830
Related parts for DF2166VTE33
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![DF21-40P-0.6PTB](/images/no-image3.png)
Part Number:
Description:
0.6mm Pitch Board-to-Fine-Coaxial Cable Connectors
Manufacturer:
Hirose Electric
Datasheet:
![DF21-30P-0.6PTB](/images/no-image3.png)
Part Number:
Description:
0.6mm Pitch Board-to-fine-coaxial Cable Connectors
Manufacturer:
Hirose Electric
Datasheet:
![DF21-20P-0.6PTB](/images/no-image3.png)
Part Number:
Description:
0.6mm Pitch Board-to-fine-coaxial Cable Connectors
Manufacturer:
Hirose Electric
Datasheet:
![DF21-20S-0.6V(56)](/images/no-image3.png)
Part Number:
Description:
Right angle, Two-piece for fine coaxial cable, Discrete wire connectors; HRS No: 687-0001-5 56; No. of Positions: 20; Connector Type: Board mounting; Contact Gender: Female; Contact Spacing (mm): 0.6; Terminal Pitch (mm): 0.6; PCB Mount Type: SMT; Cu
Manufacturer:
Hirose Electric
![DF21-20P-0.6SD](/images/no-image3.png)
Part Number:
Description:
0.6mm Pitch Board-to-fine-coaxial Cable Connectors
Manufacturer:
Hirose Electric
Datasheet:
![DF21-20P-0.6SD-GND](/images/no-image3.png)
Part Number:
Description:
0.6mm Pitch Board-to-Fine-Coaxial Cable Connectors
Manufacturer:
HIROSE [Hirose Electric]
Datasheet:
![R0K330290S001BE](/photos/28/41/284146/r0k330290s001be_tmb.jpg)
Part Number:
Description:
KIT STARTER FOR M16C/29
Manufacturer:
Renesas Electronics America
Datasheet:
![R0K5212D8S001BE](/photos/24/13/241324/4607177_tmb.jpg)
Part Number:
Description:
KIT STARTER FOR R8C/2D
Manufacturer:
Renesas Electronics America
Datasheet:
![R0K33062PS001BE](/photos/24/13/241320/4607173_tmb.jpg)
Part Number:
Description:
R0K33062P STARTER KIT
Manufacturer:
Renesas Electronics America
Datasheet:
![R0K521237S001BE](/photos/28/41/284170/r0k521237s001be_tmb.jpg)
Part Number:
Description:
KIT STARTER FOR R8C/23 E8A
Manufacturer:
Renesas Electronics America
Datasheet:
![R0K521256S001BE](/photos/24/13/241323/4607176_tmb.jpg)
Part Number:
Description:
KIT STARTER FOR R8C/25
Manufacturer:
Renesas Electronics America
Datasheet:
![YLCDRSK2456S](/images/manufacturer_photos/0/5/560/renesas_electronics_america_tmb.jpg)
Part Number:
Description:
KIT STARTER H8S2456 SHARPE DSPLY
Manufacturer:
Renesas Electronics America
Datasheet:
![R0K521380S000BE](/photos/28/41/284144/r0k521380s000be_tmb.jpg)
Part Number:
Description:
KIT STARTER FOR R8C38C
Manufacturer:
Renesas Electronics America
Datasheet:
![R0K521350S000BE](/photos/28/41/284145/r0k521350s000be_tmb.jpg)
Part Number:
Description:
KIT STARTER FOR R8C35C
Manufacturer:
Renesas Electronics America
Datasheet:
![R0K52L3A0S000BE](/photos/28/41/284149/r0k52l3a0s000be_tmb.jpg)
Part Number:
Description:
KIT STARTER FOR R8CL3AC+LCD APPS
Manufacturer:
Renesas Electronics America
Datasheet: