MC9S08SH16MTG Freescale Semiconductor, MC9S08SH16MTG Datasheet - Page 59

• Manufacturer Part Number: MC9S08SH16MTG
• Description: MCU 8BIT 16K FLASH 16-TSSOP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08SH16MTG

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 13
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 16-TSSOP
• Core: S08
• Processor Series: MC9S08Sxx
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 40 MHz
• Data Ram Size: 1 KB
• On-chip Adc: Yes
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.5 V
• Operating Temperature Range: - 40 C to + 125 C
• Mounting Style: SMD/SMT
• A/d Bit Size: 10 bit
• A/d Channels Available: 8
• Height: 1.05 mm
• Interface Type: SCI, SPI, I2C
• Length: 5 mm
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Width: 4.4 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Chapter 5
Resets, Interrupts, and General System Control
5.1
This section discusses basic reset and interrupt mechanisms and the various sources of reset and interrupt
in the MC9S08SH32 Series. Some interrupt sources from peripheral modules are discussed in greater
detail within other sections of this data sheet. This section gathers basic information about all reset and
interrupt sources in one place for easy reference. A few reset and interrupt sources, including the computer
operating properly (COP) watchdog are not part of on-chip peripheral systems with their own chapters.
5.2
Reset and interrupt features include:
5.3
Resetting the MCU provides a way to start processing from a known set of initial conditions. During reset,
most control and status registers are forced to initial values and the program counter is loaded from the
reset vector (0xFFFE:0xFFFF). On-chip peripheral modules are disabled and I/O pins are initially
configured as general-purpose high-impedance inputs with pull-up devices disabled. The I bit in the
condition code register (CCR) is set to block maskable interrupts so the user program has a chance to
initialize the stack pointer (SP) and system control settings. SP is forced to 0x00FF at reset.
The MC9S08SH32 Series has the following sources for reset:
Each of these sources, with the exception of the background debug forced reset, has an associated bit in
the system reset status register (SRS).
Freescale Semiconductor
•
•
•
•
•
•
•
•
•
•
Multiple sources of reset for flexible system configuration and reliable operation
System reset status register (SRS) to indicate source of most recent reset
Separate interrupt vector for each module (reduces polling overhead) (see
Power-on reset (POR)
External pin reset (PIN) - enabled using RSTPE in SOPT1
Low-voltage detect (LVD)
Computer operating properly (COP) timer
Illegal opcode detect (ILOP)
Illegal address detect (ILAD) - access of any address in memory map that is listed as
unimplemented will produce an illegal address reset
Background debug forced reset
Introduction
Features
MCU Reset
MC9S08SH32 Series Data Sheet, Rev. 2
PRELIMINARY
Table
5-2)
59