MC9S08SH16MTG Freescale Semiconductor, MC9S08SH16MTG Datasheet - Page 188

• Manufacturer Part Number: MC9S08SH16MTG
• Description: MCU 8BIT 16K FLASH 16-TSSOP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08SH16MTG

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 13
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 16-TSSOP
• Core: S08
• Processor Series: MC9S08Sxx
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 40 MHz
• Data Ram Size: 1 KB
• On-chip Adc: Yes
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.5 V
• Operating Temperature Range: - 40 C to + 125 C
• Mounting Style: SMD/SMT
• A/d Bit Size: 10 bit
• A/d Channels Available: 8
• Height: 1.05 mm
• Interface Type: SCI, SPI, I2C
• Length: 5 mm
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Width: 4.4 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Chapter 12 Modulo Timer (S08MTIMV1)
12.3.1
MTIMSC contains the overflow status flag and control bits which are used to configure the interrupt
enable, reset the counter, and stop the counter.
188
TRST
TSTP
Field
TOIE
TOF
3:0
7
6
5
4
Reset:
W
R
MTIM Overflow Flag — This read-only bit is set when the MTIM counter register overflows to $00 after reaching
the value in the MTIM modulo register. Clear TOF by reading the MTIMSC register while TOF is set, then writing
a 0 to TOF. TOF is also cleared when TRST is written to a 1 or when any value is written to the MTIMMOD register.
0 MTIM counter has not reached the overflow value in the MTIM modulo register.
1 MTIM counter has reached the overflow value in the MTIM modulo register.
MTIM Overflow Interrupt Enable — This read/write bit enables MTIM overflow interrupts. If TOIE is set, then an
interrupt is generated when TOF = 1. Reset clears TOIE. Do not set TOIE if TOF = 1. Clear TOF first, then set TOIE.
0 TOF interrupts are disabled. Use software polling.
1 TOF interrupts are enabled.
MTIM Counter Reset — When a 1 is written to this write-only bit, the MTIM counter register resets to $00 and TOF
is cleared. Reading this bit always returns 0.
0 No effect. MTIM counter remains at current state.
1 MTIM counter is reset to $00.
MTIM Counter Stop — When set, this read/write bit stops the MTIM counter at its current value. Counting resumes
from the current value when TSTP is cleared. Reset sets TSTP to prevent the MTIM from counting.
0 MTIM counter is active.
1 MTIM counter is stopped.
Unused register bits, always read 0.
MTIM Status and Control Register (MTIMSC)
TOF
7
0
Table 12-2. MTIM Status and Control Register Field Descriptions
TOIE
Figure 12-4. MTIM Status and Control Register
0
6
MC9S08SH32 Series Data Sheet, Rev. 2
TRST
0
0
5
PRELIMINARY
TSTP
1
4
Description
0
0
3
0
0
2
Freescale Semiconductor
0
0
1
0
0
0