MC9S08SH16MTG Freescale Semiconductor, MC9S08SH16MTG Datasheet - Page 57

• Manufacturer Part Number: MC9S08SH16MTG
• Description: MCU 8BIT 16K FLASH 16-TSSOP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08SH16MTG

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 13
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 16-TSSOP
• Core: S08
• Processor Series: MC9S08Sxx
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 40 MHz
• Data Ram Size: 1 KB
• On-chip Adc: Yes
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.5 V
• Operating Temperature Range: - 40 C to + 125 C
• Mounting Style: SMD/SMT
• A/d Bit Size: 10 bit
• A/d Channels Available: 8
• Height: 1.05 mm
• Interface Type: SCI, SPI, I2C
• Length: 5 mm
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Width: 4.4 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

4.7.5
Freescale Semiconductor
Reset
FPVIOL
FCBEF
FPDIS
FCCF
Field
Field
FPS
7:1
0
7
6
5
W
R
FCBEF
FLASH Status Register (FSTAT)
FLASH Protect Select Bits — When FPDIS = 0, this 7-bit field determines the ending address of unprotected
FLASH locations at the high address end of the FLASH. Protected FLASH locations cannot be erased or
programmed.
FLASH Protection Disable
0 FLASH block specified by [7:1] is block protected (program and erase not allowed).
1 No FLASH block is protected.
FLASH Command Buffer Empty Flag — The FCBEF bit is used to launch commands. It also indicates that the
command buffer is empty so that a new command sequence can be executed when performing burst
programming. The FCBEF bit is cleared by writing a 1 to it or when a burst program command is transferred to
the array for programming. Only burst program commands can be buffered.
0 Command buffer is full (not ready for additional commands).
1 A new burst program command can be written to the command buffer.
FLASH Command Complete Flag — FCCF is set automatically when the command buffer is empty and no
command is being processed. FCCF is cleared automatically when a new command is started (by writing 1 to
FCBEF to register a command). Writing to FCCF has no meaning or effect.
0 Command in progress
1 All commands complete
Protection Violation Flag — FPVIOL is set automatically when a command is written that attempts to erase or
program a location in a protected block (the erroneous command is ignored). FPVIOL is cleared by writing a 1
to FPVIOL.
0 No protection violation.
1 An attempt was made to erase or program a protected location.
1
7
= Unimplemented or Reserved
FCCF
1
6
Table 4-11. FPROT Register Field Descriptions
Table 4-12. FSTAT Register Field Descriptions
Figure 4-9. FLASH Status Register (FSTAT)
FPVIOL
MC9S08SH32 Series Data Sheet, Rev. 2
0
5
PRELIMINARY
FACCERR
0
4
Description
Description
3
0
0
FBLANK
0
2
0
0
1
Chapter 4 Memory
0
0
0
57