ST72F324J6T6 STMicroelectronics, ST72F324J6T6 Datasheet - Page 26

• Manufacturer Part Number: ST72F324J6T6
• Description: IC MCU 8BIT 32K 44-TQFP
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST72F324J6T6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3.8 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Controller Family/series: ST7
• No. Of I/o's: 32
• Ram Memory Size: 1KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: SCI, SPI
• No. Of Pwm Channels: 1
• Rohs Compliant: Yes
• Processor Series: ST72F3x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 1024 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 4 bit
• Operating Supply Voltage: 3.8 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7F521-IND/USB, ST7232X-EVAL, ST7MDT20-DVP3, ST7MDT20J-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Cpu Family: ST7
• Device Core Size: 8b
• Frequency (max): 8MHz
• Total Internal Ram Size: 1KB
• # I/os (max): 32
• Number Of Timers - General Purpose: 2
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 3.8V
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 44
• Package Type: TQFP
• For Use With: 497-8222 - UPS (LINE INTERACTIVE - 450W)497-8436 - BOARD EVAL UPS 450W VOUT=220V497-6421 - BOARD EVAL DGTL BATT CHGR DESIGN
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: In Transition
• Other names: 497-2108

Flash program memory
4.5
4.6
4.7
4.7.1
26/193
ICP (in-circuit programming)
To perform ICP the microcontroller must be switched to ICC (in-circuit communication) mode
by an external controller or programming tool.
Depending on the ICP code downloaded in RAM, Flash memory programming can be fully
customized (number of bytes to program, program locations, or selection serial
communication interface for downloading).
When using an STMicroelectronics or third-party programming tool that supports ICP and
the specific microcontroller device, the user needs only to implement the ICP hardware
interface on the application board (see
to the device pinout description.
IAP (in-application programming)
This mode uses a BootLoader program previously stored in Sector 0 by the user (in ICP
mode or by plugging the device in a programming tool).
This mode is fully controlled by user software. This allows it to be adapted to the user
application, (such as user-defined strategy for entering programming mode, choice of
communications protocol used to fetch the data to be stored). For example, it is possible to
download code from the SPI, SCI, USB or CAN interface and program it in the Flash. IAP
mode can be used to program any of the Flash sectors except Sector 0, which is write/erase
protected to allow recovery in case errors occur during the programming operation.
Related documentation
For details on Flash programming and ICC protocol, refer to the ST7 Flash Programming
Reference Manual and to the ST7 ICC Protocol Reference Manual
Flash Control/Status Register (FCSR)
This register is reserved for use by programming tool software. It controls the Flash
programming and erasing operations.
Table 5.
FCSR
Address (Hex)
R/W
7
0
0029h
Flash control/status register address and reset value
R/W
6
0
FCSR reset value
Register label
R/W
5
0
7
0
R/W
Figure
4
0
6
0
8). For more details on the pin locations, refer
R/W
3
0
5
0
4
0
R/W
2
0
Reset value:
3
0
.
R/W
2
0
1
0
0000 0000 (00h)
ST72324Bxx
1
0
R/W
0
0
0
0