AT32UC3B064-Z2UR Atmel, AT32UC3B064-Z2UR Datasheet - Page 394
![MCU AVR32 64K FLASH 64-QFN](/photos/12/13/121326/313-64-qfn_sml.jpg)
AT32UC3B064-Z2UR
Manufacturer Part Number
AT32UC3B064-Z2UR
Description
MCU AVR32 64K FLASH 64-QFN
Manufacturer
Atmel
Series
AVR®32 UC3r
Datasheet
1.AT32UC3B164-AUR.pdf
(680 pages)
Specifications of AT32UC3B064-Z2UR
Package / Case
64-QFN
Voltage - Supply (vcc/vdd)
1.65 V ~ 1.95 V
Operating Temperature
-40°C ~ 85°C
Speed
60MHz
Number Of I /o
44
Core Processor
AVR
Program Memory Type
FLASH
Ram Size
16K x 8
Program Memory Size
64KB (64K x 8)
Data Converters
A/D 8x10b
Oscillator Type
Internal
Peripherals
Brown-out Detect/Reset, DMA, POR, PWM, WDT
Connectivity
I²C, IrDA, SPI, SSC, UART/USART, USB
Core Size
32-Bit
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
- Current page: 394 of 680
- Download datasheet (10Mb)
22.7.3.3
22.7.3.4
22.7.3.5
22.7.3.6
32059J–12/2010
Device detection
USB reset
Pipe reset
Pipe activation
sumption. The USB pad should be in the Idle state. Once a device is connected, the macro
enters the Ready state, what does not require the USB clock to be activated.
The controller enters the Suspend state when the USB bus is in a “Suspend” state, i.e., when
the host mode does not generate the “Start of Frame (SOF)”. In this state, the USB consumption
is minimal. The host mode exits the Suspend state when starting to generate the SOF over the
USB line.
A device is detected by the USBB host mode when D+ or D- is no longer tied low, i.e., when the
device D+ or D- pull-up resistor is connected. To enable this detection, the host controller has to
provide the VBus power supply to the device by setting the VBUSRQ bit (by writing a one to the
VBUSRQS bit).
The device disconnection is detected by the host controller when both D+ and D- are pulled
down.
The USBB sends a USB bus reset when the user write a one to the Send USB Reset bit in the
Host General Control register (UHCON.RESET). The USB Reset Sent Interrupt bit in the Host
Global Interrupt register (UHINT.RSTI) is set when the USB reset has been sent. In this case, all
the pipes are disabled and de-allocated.
If the bus was previously in a “Suspend” state (the Start of Frame Generation Enable (SOFE) bit
in UHCON is zero), the USBB automatically switches it to the “Resume” state, the Host Wake-
Up Interrupt (HWUPI) bit in UHINT is set and the SOFE bit is set in order to generate SOFs
immediately after the USB reset.
A pipe can be reset at any time by writing a one to the Pipe n Reset (PRSTn) bit in the UPRST
register. This is recommended before using a pipe upon hardware reset or when a USB bus
reset has been sent. This resets:
• The internal state machine of this pipe
• The receive and transmit bank FIFO counters
• All the registers of this pipe (UPCFGn, UPSTAn, UPCONn), except its configuration (ALLOC,
The pipe configuration remains active and the pipe is still enabled.
The pipe reset may be associated with a clear of the data toggle sequence. This can be
achieved by setting the Reset Data Toggle bit in the Pipe n Control register (UPCONn.RSTDT)
(by writing a one to the Reset Data Toggle Set bit in the Pipe n Control Set register
(UPCONnSET.RSTDTS)).
In the end, the user has to write a zero to the PRSTn bit to complete the reset operation and to
start using the FIFO.
The pipe is maintained inactive and reset (see
disabled (PENn is zero). The Data Toggle Sequence field (DTSEQ) is also reset.
PBK, PSIZE, PTOKEN, PTYPE, PEPNUM, INTFRQ in UPCFGn) and its Data Toggle
Sequence field in the Pipe n Status register (UPSTAn.DTSEQ).
Section 22.7.3.5
for more details) as long as it is
AT32UC3B
394
Related parts for AT32UC3B064-Z2UR
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ATSTK600](/photos/9/20/92038/atstk600_tmb.jpg)
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
![U641B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
![U4082B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
![U4089B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
![U4255BM-M](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
![U4089B-P](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
![TDA4470](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
![ATF22V10B-25PC](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
![AT89C51ED2-IM](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
![AT24C01](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: