ATTINY24A-SSUR Atmel, ATTINY24A-SSUR Datasheet - Page 92

• Manufacturer Part Number: ATTINY24A-SSUR
• Description: MCU AVR 2KB FLASH 20MHZ 14SOIC
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY24A-SSUR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 12
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Package: 14SOIC W
• Device Core: AVR
• Family Name: ATtiny
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 12
• Interface Type: SPI/USI
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 2
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

12.6.1
12.6.2
12.6.3
12.7
92
Compare Match Output Unit
ATtiny24A/44A/84A
Force Output Compare
Compare Match Blocking by TCNT1 Write
Using the Output Compare Unit
updated by the value written. Then when the low byte (OCR1xL) is written to the lower eight bits,
the high byte will be copied into the upper 8-bits of either the OCR1x buffer or OCR1x Compare
Register in the same system clock cycle.
For more information of how to access the 16-bit registers refer to
on page
In non-PWM Waveform Generation modes, the match output of the comparator can be forced by
writing a one to the Force Output Compare (1x) bit. Forcing compare match will not set the
OCF1x flag or reload/clear the timer, but the OC1x pin will be updated as if a real compare
match had occurred (the COM1[1:0] bits settings define whether the OC1x pin is set, cleared or
toggled).
All CPU writes to the TCNT1 Register will block any compare match that occurs in the next timer
clock cycle, even when the timer is stopped. This feature allows OCR1x to be initialized to the
same value as TCNT1 without triggering an interrupt when the Timer/Counter clock is enabled.
Since writing TCNT1 in any mode of operation will block all compare matches for one timer clock
cycle, there are risks involved when changing TCNT1 when using any of the Output Compare
channels, independent of whether the Timer/Counter is running or not. If the value written to
TCNT1 equals the OCR1x value, the compare match will be missed, resulting in incorrect wave-
form generation. Do not write the TCNT1 equal to TOP in PWM modes with variable TOP
values. The compare match for the TOP will be ignored and the counter will continue to 0xFFFF.
Similarly, do not write the TCNT1 value equal to BOTTOM when the counter is downcounting.
The setup of the OC1x should be performed before setting the Data Direction Register for the
port pin to output. The easiest way of setting the OC1x value is to use the Force Output Com-
pare (1x) strobe bits in Normal mode. The OC1x Register keeps its value even when changing
between Waveform Generation modes.
Be aware that the COM1x[1:0] bits are not double buffered together with the compare value.
Changing the COM1x[1:0] bits will take effect immediately.
The Compare Output Mode (COM1x[1:0]) bits have two functions. The Waveform Generator
uses the COM1x[1:0] bits for defining the Output Compare (OC1x) state at the next compare
match. Secondly the COM1x[1:0] bits control the OC1x pin output source.
93
isters, I/O bits, and I/O pins in the figure are shown in bold. Only the parts of the general I/O port
control registers (DDR and PORT) that are affected by the COM1x[1:0] bits are shown. When
referring to the OC1x state, the reference is for the internal OC1x Register, not the OC1x pin. If
a system reset occur, the OC1x Register is reset to “0”.
shows a simplified schematic of the logic affected by the COM1x[1:0] bit setting. The I/O Reg-
103.
“Accessing 16-bit Registers”
Figure 12-5 on page
8183C–AVR–03/11