ATTINY24A-SSUR Atmel, ATTINY24A-SSUR Datasheet - Page 122

• Manufacturer Part Number: ATTINY24A-SSUR
• Description: MCU AVR 2KB FLASH 20MHZ 14SOIC
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY24A-SSUR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 12
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Package: 14SOIC W
• Device Core: AVR
• Family Name: ATtiny
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 12
• Interface Type: SPI/USI
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 2
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

14.3.5
14.3.6
122
ATtiny24A/44A/84A
Start Condition Detector
Clock speed considerations
If the slave is not able to receive more data it does not acknowledge the data byte it has last
received. When the master does a read operation it must terminate the operation by forcing the
acknowledge bit low after the last byte transmitted.
The start condition detector is shown in
to 300 ns) to ensure valid sampling of the SCL line. The start condition detector is only enabled
in two-wire mode.
Figure 14-6.
The start condition detector works asynchronously and can therefore wake up the processor
from power-down sleep mode. However, the protocol used might have restrictions on the SCL
hold time. Therefore, when using this feature the oscillator start-up time (set by CKSEL fuses,
see
of the USISIF bit on
Maximum frequency for SCL and SCK is f
receive rate in both two- and three-wire mode. In two-wire slave mode the Two-wire Clock Con-
trol Unit will hold the SCL low until the slave is ready to receive more data. This may reduce the
actual data rate in two-wire mode.
4. After eight bits containing slave address and data direction (read or write) have been
5. When the slave is addressed, it holds the SDA line low during the acknowledgment
6. Multiple bytes can now be transmitted, all in same direction, until a stop condition is
“Clock Sources” on page
transferred, the slave counter overflows and the SCL line is forced low (D). If the slave
is not the one the master has addressed, it releases the SCL line and waits for a new
start condition.
cycle before holding the SCL line low again (i.e., the USI Counter Register must be set
to 14 before releasing SCL at (D)). Depending on the R/W bit the master or slave
enables its output. If the bit is set, a master read operation is in progress (i.e., the slave
drives the SDA line) The slave can hold the SCL line low after the acknowledge (E).
given by the master (F), or a new start condition is given.
Write( USISIF)
Start Condition Detector, Logic Diagram
page 128
SDA
SCL
25) must also be taken into consideration. Refer to the description
for further details.
Figure
CK
/ 2. This is also the maximum data transmit and
14-6. The SDA line is delayed (in the range of 50
D Q
CLR
D Q
CLR
USISIF
CLOCK
HOLD
8183C–AVR–03/11