SAF-XE167G-72F66L AC Infineon Technologies, SAF-XE167G-72F66L AC Datasheet - Page 68
![IC MCU 16BIT FLASH PG-LQFP-144](/photos/12/23/122331/saf-xe167g-72f66l_ac_sml.jpg)
SAF-XE167G-72F66L AC
Manufacturer Part Number
SAF-XE167G-72F66L AC
Description
IC MCU 16BIT FLASH PG-LQFP-144
Manufacturer
Infineon Technologies
Series
XE16xr
Datasheet
1.SAF-XE167K-96F66L_AC.pdf
(122 pages)
Specifications of SAF-XE167G-72F66L AC
Core Processor
C166SV2
Core Size
16-Bit
Speed
66MHz
Connectivity
CAN, EBI/EMI, I²C, LIN, SPI, SSC, UART/USART, USI
Peripherals
I²S, POR, PWM, WDT
Number Of I /o
118
Program Memory Size
576KB (576K x 8)
Program Memory Type
FLASH
Ram Size
50K x 8
Voltage - Supply (vcc/vdd)
3 V ~ 5.5 V
Data Converters
A/D 16x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
144-LFQFP
Data Bus Width
16 bit
Data Ram Size
32 KB
Interface Type
CAN
Maximum Clock Frequency
66 MHz
Number Of Programmable I/os
118
Number Of Timers
11
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 24 Channel
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
Details
Other names
FXE167G72F66LACXP
SAF-XE167G-72F66LACIN
SP000363815
SAF-XE167G-72F66LACIN
SP000363815
3.13
The Watchdog Timer is one of the fail-safe mechanisms which have been implemented
to prevent the controller from malfunctioning for longer periods of time.
The Watchdog Timer is always enabled after an application reset of the chip. It can be
disabled and enabled at any time by executing the instructions DISWDT and ENWDT
respectively. The software has to service the Watchdog Timer before it overflows. If this
is not the case because of a hardware or software failure, the Watchdog Timer
overflows, generating a prewarning interrupt and then a reset request.
The Watchdog Timer is a 16-bit timer clocked with the system clock divided by 16,384
or 256. The Watchdog Timer register is set to a prespecified reload value (stored in
WDTREL) in order to allow further variation of the monitored time interval. Each time it
is serviced by the application software, the Watchdog Timer is reloaded and the
prescaler is cleared.
Time intervals between 3.2 µs and 13.4 s can be monitored (@ 80 MHz).
The default Watchdog Timer interval after power-up is 6.5 ms (@ 10 MHz).
3.14
The Clock Generation Unit can generate the system clock signal
a number of external or internal clock sources:
•
•
•
•
The programmable on-chip PLL with multiple prescalers generates a clock signal for
maximum system performance from standard crystals or from the on-chip clock source.
See also
The Oscillator Watchdog (OWD) generates an interrupt if the crystal oscillator frequency
falls below a certain limit or stops completely. In this case, the system can be supplied
with an emergency clock to enable operation even after an external clock failure.
All available clock signals can be output on one of two selectable pins.
Data Sheet
External clock signals with pad or core voltage levels
External crystal using the on-chip oscillator
On-chip clock source for operation without crystal
Wake-up clock (ultra-low-power) to further reduce power consumption
Section
Watchdog Timer
Clock Generation
4.6.2.
66
XE166 Family Derivatives
Functional Description
f
SYS
for the XE167 from
V2.1, 2008-08
XE167x