MC56F8322MFAE Freescale Semiconductor, MC56F8322MFAE Datasheet - Page 94

• Manufacturer Part Number: MC56F8322MFAE
• Description: IC DSP 16BIT 60MHZ 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: 56F8xxxr

Specifications of MC56F8322MFAE

• Core Processor: 56800
• Core Size: 16-Bit
• Speed: 60MHz
• Connectivity: CAN, SCI, SPI
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 21
• Program Memory Size: 40KB (20K x 16)
• Program Memory Type: FLASH
• Ram Size: 6K x 16
• Voltage - Supply (vcc/vdd): 2.25 V ~ 3.6 V
• Data Converters: A/D 6x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 48-LQFP
• Cpu Family: 56F8xxx
• Device Core Size: 16b
• Frequency (max): 60MHz
• Interface Type: CAN/SCI/SPI
• Total Internal Ram Size: 4KB
• # I/os (max): 21
• Number Of Timers - General Purpose: 2
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 2.75/3.6V
• Operating Supply Voltage (min): 2.25/3V
• On-chip Adc: 2(3-chx12-bit)
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Data Bus Width: 16 bit
• Processor Series: MC56F83xx
• Core: 56800E
• Numeric And Arithmetic Format: Fixed-Point
• Device Million Instructions Per Second: 40 MIPs
• Maximum Clock Frequency: 60 MHz
• Number Of Programmable I/os: 21
• Data Ram Size: 4 KB
• Operating Supply Voltage: - 0.3 V to + 4 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Data Rom Size: 8 KB
• Minimum Operating Temperature: - 40 C
• For Use With: MC56F8323EVME - BOARD EVALUATION MC56F8323
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

6.8 Stop and Wait Mode Disable Function
The 56800E core contains both STOP and WAIT instructions. Both put the CPU to sleep. For lowest
power consumption in Stop mode, the PLL can be shut down. This must be done explicitly before entering
Stop mode, since there is no automatic mechanism for this. When the PLL is shut down, the 56800E
system clock must be set equal to the prescaler output.
Some applications require the 56800E STOP and WAIT instructions be disabled. To disable those
instructions, write to the SIM control register (SIM_CONTROL) described in
procedure can be on either a permanent or temporary basis. Permanently assigned applications last only
until their next reset.
6.9 Resets
The SIM supports four sources of reset. The two asynchronous sources are the external RESET pin and
the Power-On Reset (POR). The two synchronous sources are the software reset, which is generated within
the SIM itself, by writing to the SIM_CONTROL register, and the COP reset.
Reset begins with the assertion of any of the reset sources. Release of reset to various blocks is sequenced
to permit proper operation of the device. A POR reset is declared when reset is removed and any of the
three voltage detectors (1.8V POR, 2.2V core voltage, or 2.7V I/O voltage) indicate a low supply voltage
condition. POR will continue to be asserted until all voltage detectors indicate a stable supply is available
(note that as power is removed POR is not declared until the 1.8V core voltage threshold is reached.) A
POR reset is then extended for 64 clock cycles to permit stabilization of the clock source, followed by a
32 clock window in which SIM clocking is initiated. It is then followed by a 32 clock window in which
peripherals are released to implement Flash security, and, finally, followed by a 32 clock window in which
the core is initialized. After completion of the described reset sequence, application code will begin
execution.
Resets may be asserted asynchronously, but are always released internally on a rising edge of the system
clock.
94
Permanent
Disable
Reprogrammable
Disable
Clock
Select
Figure 6-16 Internal Stop Disable Circuit
Reset
56F8322 Techncial Data, Rev. 16
D-FLOP
D
D
C
D
D-FLOP
C R
Q
Q
Note: Wait disable circuit is similar
STOP_DIS
56800E
Freescale Semiconductor
Section 6.5.1
Preliminary
. This