C8051F327-GM Silicon Laboratories Inc, C8051F327-GM Datasheet - Page 130

• Manufacturer Part Number: C8051F327-GM
• Description: IC 8051 MCU FLASH 16K 28QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F32xr

Specifications of C8051F327-GM

• Program Memory Type: FLASH
• Program Memory Size: 16KB (16K x 8)
• Package / Case: 28-QFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: UART/USART, USB
• Peripherals: POR
• Number Of I /o: 15
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 1.5 KB
• Interface Type: UART/USB
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 15
• Number Of Timers: 2
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F326DK
• Minimum Operating Temperature: - 40 C
• Package: 28QFN EP
• Device Core: 8051
• Family Name: C8051F327
• Maximum Speed: 25 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1481 - DAUGHTER CARD TOOLSTCK C8051F327770-1006 - ISP 4PORT FOR SILABS C8051F MCU
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1297-5

C8051F326/7
14.1.4. Mode 3: Two 8-bit Timers (Timer 0 Only)
In Mode 3, Timer 0 is configured as two separate 8-bit timers held in TL0 and TH0. The counter in TL0 is
controlled using the Timer 0 control/status bits in TCON and TMOD: TR0, C/T0, GATE0 and TF0. TL0 can
use either the system clock or an external input signal as its timebase. The TH0 register is restricted to a
timer function sourced by the system clock or prescaled clock. TH0 is enabled using the Timer 1 run con-
trol bit TR1. TH0 sets the Timer 1 overflow flag TF1 on overflow and thus controls the Timer 1 interrupt.
Timer 1 is inactive in Mode 3. When Timer 0 is operating in Mode 3, Timer 1 can be operated in Modes 0,
1 or 2, but cannot set the TF1 flag and generate an interrupt. However, the Timer 1 overflow can be used to
generate baud rates for the UART. While Timer 0 is operating in Mode 3, Timer 1 run control is handled
through its mode settings. To run Timer 1 while Timer 0 is in Mode 3, set the Timer 1 Mode as 0, 1, or 2. To
disable Timer 1, configure it for Mode 3.
130
G
A
T
E
1
C
T
1
/
M
T
1
1
TMOD
M
T
1
0
G
A
T
E
0
C
T
0
/
M
T
0
1
M
T
0
0
Pre-scaled Clock
SYSCLK
GATE0
/INT0
Figure 14.3. T0 Mode 3 Block Diagram
CKCON
M
T
1
TR0
M
T
0
0
1
S
C
A
1
S
C
A
0
Rev. 1.1
TR1
(8 bits)
(8 bits)
TH0
TL0
TF1
TR1
TF0
TR0
IE1
IT1
IE0
IT0
Interrupt
Interrupt