C8051F327-GM Silicon Laboratories Inc, C8051F327-GM Datasheet - Page 105

• Manufacturer Part Number: C8051F327-GM
• Description: IC 8051 MCU FLASH 16K 28QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F32xr

Specifications of C8051F327-GM

• Program Memory Type: FLASH
• Program Memory Size: 16KB (16K x 8)
• Package / Case: 28-QFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: UART/USART, USB
• Peripherals: POR
• Number Of I /o: 15
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 1.5 KB
• Interface Type: UART/USB
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 15
• Number Of Timers: 2
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F326DK
• Minimum Operating Temperature: - 40 C
• Package: 28QFN EP
• Device Core: 8051
• Family Name: C8051F327
• Maximum Speed: 25 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1481 - DAUGHTER CARD TOOLSTCK C8051F327770-1006 - ISP 4PORT FOR SILABS C8051F MCU
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1297-5

12.10.2.Endpoint0 IN Transactions
When a SETUP request is received that requires USB0 to transmit data to the host, one or more IN
requests will be sent by the host. For the first IN transaction, firmware should load an IN packet into the
Endpoint0 FIFO, and set the INPRDY bit (E0CSR.1). An interrupt will be generated when an IN packet is
transmitted successfully. Note that no interrupt will be generated if an IN request is received before firm-
ware has loaded a packet into the Endpoint0 FIFO. If the requested data exceeds the maximum packet
size for Endpoint0 (as reported to the host), the data should be split into multiple packets; each packet
should be of the maximum packet size excluding the last (residual) packet. If the requested data is an inte-
ger multiple of the maximum packet size for Endpoint0, the last data packet should be a zero-length packet
signaling the end of the transfer. Firmware should set the DATAEND bit to ‘1’ after loading into the
Endpoint0 FIFO the last data packet for a transfer.
Upon reception of the first IN token for a particular control transfer, Endpoint0 is said to be in Transmit
Mode. In this mode, only IN tokens should be sent by the host to Endpoint0. The SUEND bit (E0CSR.4) is
set to ‘1’ if a SETUP or OUT token is received while Endpoint0 is in Transmit Mode.
Endpoint0 will remain in Transmit Mode until any of the following occur:
Firmware should set the DATAEND bit (E0CSR.3) to ‘1’ when performing (2) and (3) above.
The SIE will transmit a NAK in response to an IN token if there is no packet ready in the IN FIFO
(INPRDY = ‘0’).
12.10.3.Endpoint0 OUT Transactions
When a SETUP request is received that requires the host to transmit data to USB0, one or more OUT
requests will be sent by the host. When an OUT packet is successfully received by USB0, hardware will set
the OPRDY bit (E0CSR.0) to ‘1’ and generate an Endpoint0 interrupt. Following this interrupt, firmware
should unload the OUT packet from the Endpoint0 FIFO and set the SOPRDY bit (E0CSR.6) to ‘1’.
If the amount of data required for the transfer exceeds the maximum packet size for Endpoint0, the data
will be split into multiple packets. If the requested data is an integer multiple of the maximum packet size
for Endpoint0 (as reported to the host), the host will send a zero-length data packet signaling the end of the
transfer.
Upon reception of the first OUT token for a particular control transfer, Endpoint0 is said to be in Receive
Mode. In this mode, only OUT tokens should be sent by the host to Endpoint0. The SUEND bit (E0CSR.4)
is set to ‘1’ if a SETUP or IN token is received while Endpoint0 is in Receive Mode.
Endpoint0 will remain in Receive mode until:
Firmware should set the DATAEND bit (E0CSR.3) to ‘1’ when the expected amount of data has been
received. The SIE will transmit a STALL condition if the host sends an OUT packet after the DATAEND bit
has been set by firmware. An interrupt will be generated with the STSTL bit (E0CSR.2) set to ‘1’ after the
STALL is transmitted.
1. USB0 receives an Endpoint0 SETUP or OUT token.
2. Firmware sends a packet less than the maximum Endpoint0 packet size.
3. Firmware sends a zero-length packet.
1. The SIE receives a SETUP or IN token.
2. The host sends a packet less than the maximum Endpoint0 packet size.
3. The host sends a zero-length packet.
Rev. 1.1
C8051F326/7
105