PIC16F76-I/ML Microchip Technology, PIC16F76-I/ML Datasheet - Page 237

• Manufacturer Part Number: PIC16F76-I/ML
• Description: IC MCU FLASH 8KX14 A/D 28QFN
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F76-I/ML

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 14KB (8K x 14)
• Program Memory Type: FLASH
• Ram Size: 368 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 5x8b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 368 B
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 22
• Number Of Timers: 3 bit
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: ICE2000, DM163022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 5 bit
• For Use With: XLT28QFN4 - SOCKET TRANS ICE 28QFN W/CABLEAC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: PIC16F76-I/MLR; PIC16F76-I/MLR; PIC16F76I/ML

1997 Microchip Technology Inc.
The SSP module has five registers for I
• SSP Control Register (SSPCON)
• SSP Status Register (SSPSTAT)
• Serial Receive/Transmit Buffer (SSPBUF)
• SSP Shift Register (SSPSR) - Not directly accessible
• SSP Address Register (SSPADD)
The SSPCON register allows control of the I
(SSPCON<3:0>) allow one of the following I
• I
• I
• I
• I
• I
Before selecting any I
the appropriate TRIS bits. Selecting an I
and SDA pins to be used as the clock and data lines in I
The SSPSTAT register gives the status of the data transfer. This information includes detection
of a START or STOP bit, specifies if the received byte was data or address, if the next byte is the
completion of 10-bit address, and if this will be a read or write data transfer.
The SSPBUF is the register to which transfer data is written to or read from. The SSPSR register
shifts the data in or out of the device. In receive operations, the SSPBUF and SSPSR create a
doubled buffered receiver. This allows reception of the next byte to begin before reading the last
byte of received data. When the complete byte is received, it is transferred to the SSPBUF reg-
ister and flag bit SSPIF is set. If another complete byte is received before the SSPBUF register
is read, a receiver overflow has occurred and the SSPOV bit (SSPCON<6>) is set and the byte
in the SSPSR is lost.
The SSPADD register holds the slave address. In 10-bit mode, the user needs to write the high
byte of the address (1111 0 A9 A8 0). Following the high byte address match, the low byte of
the address needs to be loaded (A7:A0).
2
2
2
2
2
C Slave mode (7-bit address)
C Slave mode (10-bit address)
C Firmware controlled Multi-Master mode (start and stop bit interrupts enabled)
C Firmware controlled Multi-Master mode (start and stop bit interrupts enabled)
C Firmware controlled Master mode, slave is idle
2
C mode, the SCL and SDA pins must be programmed to inputs by setting
2
C operation. They are:
2
C mode, by setting the SSPEN bit, enables the SCL
2
C modes to be selected:
2
C operation. Four mode selection bits
Section 15. SSP
2
C mode.
DS31015A-page 15-17
15