PIC18F86J90-I/PT Microchip Technology, PIC18F86J90-I/PT Datasheet - Page 272

• Manufacturer Part Number: PIC18F86J90-I/PT
• Description: IC PIC MCU FLASH 64KB 80-TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F86J90-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 64KB (32K x 16)
• Package / Case: 80-TFQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, LVD, POR, PWM, WDT
• Number Of I /o: 67
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3923 B
• Interface Type: AUSART, EUSART, I2C, SPI
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 67
• Number Of Timers: 4
• Operating Supply Voltage: 2.65 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 12 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC162079 - HEADER MPLAB ICD2 18F85J90 64/80AC164328 - MODULE SKT FOR 80TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F87J90 FAMILY
19.4.2
Once Synchronous mode is selected, reception is
enabled by setting either the Single Receive Enable bit,
SREN (RCSTA1<5>), or the Continuous Receive
Enable bit, CREN (RCSTA1<4>). Data is sampled on
the RX1 pin on the falling edge of the clock.
If enable bit, SREN, is set, only a single word is
received. If enable bit, CREN, is set, the reception is
continuous until CREN is cleared. If both bits are set,
then CREN takes precedence.
To set up a Synchronous Master Reception:
1.
2.
FIGURE 19-13:
TABLE 19-8:
DS39933D-page 272
INTCON
PIR1
PIE1
IPR1
RCSTA1
RCREG1
TXSTA1
BAUDCON1 ABDOVF
SPBRGH1
SPBRG1
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for synchronous master reception.
RC6/TX1/CK1/SEG27
RC6/TX1/CK1/SEG27
Note: Timing diagram demonstrates Sync Master mode with bit, SREN = 1, and bit, BRGH = 0.
Name
Initialize the SPBRGH1:SPBRG1 registers for the
appropriate baud rate. Set or clear the BRG16 bit,
as required, to achieve the desired baud rate.
Enable the synchronous master serial port by
setting bits, SYNC, SPEN and CSRC.
Pin (SCKP = 0)
Pin (SCKP = 1)
RC7/RX1/DT1/
SEG28 Pin
(Interrupt)
RCREG1
CREN bit
RC1IF bit
SREN bit
SREN bit
EUSART SYNCHRONOUS
MASTER RECEPTION
Write to
Read
EUSART Receive Register
EUSART Baud Rate Generator Register High Byte
EUSART Baud Rate Generator Register Low Byte
GIE/GIEH PEIE/GIEL TMR0IE
CSRC
SPEN
Q2
Bit 7
REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER RECEPTION
—
—
—
Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
‘0’
SYNCHRONOUS RECEPTION (MASTER MODE, SREN)
RCIDL
ADIE
ADIP
ADIF
Bit 6
RX9
TX9
bit 0
RXDTP
RC1IE
RC1IP
RC1IF
SREN
TXEN
Bit 5
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
bit 1
TXCKP
INT0IE
bit 2
CREN
TX1IF
TX1IE
TX1IP
SYNC
Bit 4
bit 3
ADDEN
SENDB
BRG16
3.
4.
5.
6.
7.
8.
9.
10. If any error occurred, clear the error by clearing
11. If using interrupts, ensure that the GIE and PEIE
SSPIE
SSPIP
SSPIF
RBIE
Bit 3
Ensure bits, CREN and SREN, are clear.
If interrupts are desired, set enable bit, RC1IE.
If 9-bit reception is desired, set bit, RX9.
If a single reception is required, set bit, SREN.
For continuous reception, set bit, CREN.
Interrupt flag bit, RC1IF, will be set when recep-
tion is complete and an interrupt will be generated
if the enable bit, RC1IE, was set.
Read the RCSTA1 register to get the 9th bit (if
enabled) and determine if any error occurred
during reception.
Read the 8-bit received data by reading the
RCREG1 register.
bit, CREN.
bits in the INTCON register (INTCON<7:6>) are
set.
bit 4
TMR0IF
BRGH
FERR
Bit 2
—
—
—
—
bit 5
TMR2IE
TMR2IP
TMR2IF
INT0IF
OERR
TRMT
 2010 Microchip Technology Inc.
WUE
Bit 1
bit 6
TMR1IF
TMR1IE
TMR1IP
ABDEN
RX9D
TX9D
RBIF
bit 7
Bit 0
Q1 Q2 Q3 Q4
on Page
Values
Reset
59
62
62
62
61
61
61
63
63
61
‘0’