PIC16F88-I/P Microchip Technology, PIC16F88-I/P Datasheet - Page 76

• Manufacturer Part Number: PIC16F88-I/P
• Description: IC MCU FLASH 4KX14 EEPROM 18DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F88-I/P

• Program Memory Type: FLASH
• Program Memory Size: 7KB (4K x 14)
• Package / Case: 18-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Eeprom Size: 256 x 8
• Ram Size: 368 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 7x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 368 B
• Interface Type: SSP/USART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 3
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163014
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 7-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: ACICE0202 - ADAPTER MPLABICE 18P 300 MILAC164010 - MODULE SKT PROMATEII DIP/SOIC
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC16F87/88
7.5
If control bit T1SYNC (T1CON<2>) is set, the external
clock input is not synchronized. The timer continues to
increment asynchronous to the internal phase clocks.
The timer will continue to run during SLEEP and can
generate an interrupt on overflow that will wake-up the
processor. However, special precautions in software
are needed to read/write the timer (Section 7.5.1
“Reading and Writing Timer1 in Asynchronous
Counter Mode”).
In Asynchronous Counter mode, Timer1 cannot be
used as a time base for capture or compare operations.
EXAMPLE 7-1:
EXAMPLE 7-2:
DS30487B-page 74
; All interrupts are disabled
CLRF
MOVLW
MOVWF
MOVLW
MOVWF
; Re-enable the Interrupt (if required)
CONTINUE
; All interrupts are disabled
MOVF
MOVWF
MOVF
MOVWF
MOVF
SUBWF
BTFSC
GOTO
; TMR1L may have rolled over between the read of the high and low bytes.
; Reading the high and low bytes now will read a good value.
MOVF
MOVWF
MOVF
MOVWF
CONTINUE
Timer1 Operation in
Asynchronous Counter Mode
TMR1L
HI_BYTE
TMR1H, F
LO_BYTE
TMR1H, F
TMR1H, W
TMPH
TMR1L, W
TMPL
TMR1H, W
TMPH,
STATUS,Z
CONTINUE
TMR1H, W
TMPH
TMR1L, W
TMPL
W
WRITING A 16-BIT FREE-RUNNING TIMER
READING A 16-BIT FREE-RUNNING TIMER
; Clear Low byte, Ensures no rollover into TMR1H
; Value to load into TMR1H
; Write High byte
; Value to load into TMR1L
; Write Low byte
; Continue with your code
; Read high byte
; Read low byte
; Read high byte
; Sub 1st read with 2nd read
; Is result = 0
; Good 16-bit read
; Read high byte
; Read low byte
; Re-enable the Interrupt (if required)
; Continue with your code
Preliminary
7.5.1
Reading TMR1H or TMR1L, while the timer is running
from an external asynchronous clock, will ensure a
valid read (taken care of in hardware). However, the
user should keep in mind that reading the 16-bit timer
in two 8-bit values itself, poses certain problems, since
the timer may overflow between the reads.
For writes, it is recommended that the user simply stop
the timer and write the desired values. A write conten-
tion may occur by writing to the timer registers while the
register is incrementing. This may produce an
unpredictable value in the timer register.
Reading the 16-bit value requires some care. The
example
Example 7-2 demonstrate how to write to and read
Timer1 while it is running in Asynchronous mode.
codes
READING AND WRITING TIMER1 IN
ASYNCHRONOUS COUNTER
MODE
provided
 2003 Microchip Technology Inc.
in
Example 7-1
and