PIC16F88-I/P Microchip Technology, PIC16F88-I/P Datasheet - Page 109

• Manufacturer Part Number: PIC16F88-I/P
• Description: IC MCU FLASH 4KX14 EEPROM 18DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F88-I/P

• Program Memory Type: FLASH
• Program Memory Size: 7KB (4K x 14)
• Package / Case: 18-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Eeprom Size: 256 x 8
• Ram Size: 368 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 7x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 368 B
• Interface Type: SSP/USART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 3
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163014
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 7-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: ACICE0202 - ADAPTER MPLABICE 18P 300 MILAC164010 - MODULE SKT PROMATEII DIP/SOIC
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

FIGURE 11-7:
FIGURE 11-8:
TABLE 11-9:
 2003 Microchip Technology Inc.
0Bh, 8Bh,
10Bh,18Bh
0Ch
18h
1Ah
8Ch
98h
99h
Legend:
Address
Note:
RB2/SDO/RX/DT pin
Load RSR
Read
RCIF
RB2/SDO/RX/DT pin
Note:
Load RSR
Read
RCIF
x = unknown, - = unimplemented locations read as ‘0’. Shaded cells are not used for asynchronous reception.
INTCON
PIR1
RCSTA
RCREG
PIE1
TXSTA
SPBRG
This timing diagram shows a data byte followed by an address byte. The data byte is not read into the RCREG (receive buffer)
because ADDEN = 1.
This timing diagram shows a data byte followed by an address byte. The data byte is not read into the RCREG (receive buffer)
because ADDEN was not updated and still = 0.
Name
REGISTERS ASSOCIATED WITH ASYNCHRONOUS RECEPTION
USART Receive Register
Baud Rate Generator Register
START
ASYNCHRONOUS RECEPTION WITH ADDRESS DETECT
ASYNCHRONOUS RECEPTION WITH ADDRESS BYTE FIRST
START
SPEN
CSRC
Bit 7
bit
GIE
bit
—
—
bit 0
bit 0
Bit 8 = 1, Address Byte
PEIE
ADIF
ADIE
Bit 6
RX9
TX9
Bit 8 = 0, Data Byte
bit 1
bit 1
TMR0IE
SREN
TXEN
RCIE
RCIF
Bit 5
bit 8
bit 8
CREN ADDEN
SYNC
INTE
TXIE
Bit 4
TXIF
Preliminary
STOP
STOP
bit
bit
SSPIE
START
SSPIF
RBIE
START
Bit 3
—
bit
bit
Bit 8 = 1, Address Byte
Bit 8 = 0, Data Byte
bit 0
bit 0
TMR0IF
CCP1IF TMR2IF TMR1IF -000 0000
CCP1IE TMR2IE TMR1IE -000 0000
BRGH
FERR
Bit 2
OERR
TRMT
Bit 1
INTF
bit 8
bit 8
STOP
STOP
bit
bit
RX9D
Word 1
RCREG
TX9D
Bit 0
R0IF
Word 1
RCREG
PIC16F87/88
0000 000x
0000 0000
0000 -010
0000 0000
0000 000x
POR, BOR
Value on:
DS30487B-page 107
-000 0000
0000 000x
0000 0000
-000 0000
0000 -010
0000 0000
0000 000u
Value on
RESETS
all other