C8051F336DK Silicon Laboratories Inc, C8051F336DK Datasheet - Page 106
![DEV KIT FOR C8051F336](/photos/9/23/92341/c8051f336dk_sml.jpg)
C8051F336DK
Manufacturer Part Number
C8051F336DK
Description
DEV KIT FOR C8051F336
Manufacturer
Silicon Laboratories Inc
Type
MCUr
Specifications of C8051F336DK
Contents
Evaluation Board, Power Supply, USB Cables, Adapter and Documentation
Processor To Be Evaluated
C8051F33x
Interface Type
USB, UART
Operating Supply Voltage
7 V to 15 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With/related Products
C8051F336
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
336-1430
- Current page: 106 of 226
- Download datasheet (2Mb)
C8051F336/7/8/9
18. Power Management Modes
The C8051F336/7/8/9 devices have three software programmable power management modes: Idle, Stop,
and Suspend. Idle mode and Stop mode are part of the standard 8051 architecture, while Suspend mode
is an enhanced power-saving mode implemented by the high-speed oscillator peripheral.
Idle mode halts the CPU while leaving the peripherals and clocks active. In Stop mode, the CPU is halted,
all interrupts and timers (except the Missing Clock Detector) are inactive, and the internal oscillator is
stopped (analog peripherals remain in their selected states; the external oscillator is not affected). Sus-
pend mode is similar to Stop mode in that the internal oscillator and CPU are halted, but the device can
wake on events such as a Port Mismatch, Comparator low output, or a Timer 3 overflow. Since clocks are
running in Idle mode, power consumption is dependent upon the system clock frequency and the number
of peripherals left in active mode before entering Idle. Stop mode and Suspend mode consume the least
power because the majority of the device is shut down with no clocks active. SFR Definition 18.1 describes
the Power Control Register (PCON) used to control the C8051F336/7/8/9's Stop and Idle power manage-
ment modes. Suspend mode is controlled by the SUSPEND bit in the OSCICN register (SFR Definition
19.3).
Although the C8051F336/7/8/9 has Idle, Stop, and Suspend modes available, more control over the device
power can be achieved by enabling/disabling individual peripherals as needed. Each analog peripheral
can be disabled when not in use and placed in low power mode. Digital peripherals, such as timers or
serial buses, draw little power when they are not in use. Turning off oscillators lowers power consumption
considerably, at the expense of reduced functionality.
18.1. Idle Mode
Setting the Idle Mode Select bit (PCON.0) causes the hardware to halt the CPU and enter Idle mode as
soon as the instruction that sets the bit completes execution. All internal registers and memory maintain
their original data. All analog and digital peripherals can remain active during Idle mode.
Idle mode is terminated when an enabled interrupt is asserted or a reset occurs. The assertion of an
enabled interrupt will cause the Idle Mode Selection bit (PCON.0) to be cleared and the CPU to resume
operation. The pending interrupt will be serviced and the next instruction to be executed after the return
from interrupt (RETI) will be the instruction immediately following the one that set the Idle Mode Select bit.
If Idle mode is terminated by an internal or external reset, the CIP-51 performs a normal reset sequence
and begins program execution at address 0x0000.
Note: If the instruction following the write of the IDLE bit is a single-byte instruction and an interrupt occurs
during the execution phase of the instruction that sets the IDLE bit, the CPU may not wake from Idle mode
when a future interrupt occurs. Therefore, instructions that set the IDLE bit should be followed by an
instruction that has two or more opcode bytes, for example:
// in ‘C’:
PCON |= 0x01;
PCON = PCON;
; in assembly:
ORL PCON, #01h
MOV PCON, PCON
If enabled, the Watchdog Timer (WDT) will eventually cause an internal watchdog reset and thereby termi-
nate the Idle mode. This feature protects the system from an unintended permanent shutdown in the event
of an inadvertent write to the PCON register. If this behavior is not desired, the WDT may be disabled by
106
// set IDLE bit
// ... followed by a 3-cycle dummy instruction
; set IDLE bit
; ... followed by a 3-cycle dummy instruction
Rev.1.0
Related parts for C8051F336DK
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![500SAAB8M00000ACF](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
SMD/C°/SINGLE-ENDED OUTPUT SILICON OSCILLATOR
Manufacturer:
Silicon Laboratories Inc
![SI3210MFT](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![4010-DAAKF_868](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
N/A N/A/SI4010 AES KEYFOB DEMO WITH LCD RX
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![4010-DASKF_868](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
N/A N/A/SI4010 SIMPLIFIED KEY FOB DEMO WITH LED RX
Manufacturer:
Silicon Laboratories Inc
Datasheet:
![4432-SEB1 C 915](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
N/A/-40 TO 85 OC/EZLINK MODULE; F930/4432 HIGH BAND (REV E/B1)
Manufacturer:
Silicon Laboratories Inc
![4432-SEB1 D 470](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
EZLink Module; F930/4432 Low Band (rev e/B1)
Manufacturer:
Silicon Laboratories Inc
![4460-TCE10D434-EK](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
I°/4460 10 DBM RADIO TEST CARD 434 MHZ
Manufacturer:
Silicon Laboratories Inc
![4461-TSQ14D868-EK](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
I°/4461 14 DBM RADIO TEST CARD 868 MHZ
Manufacturer:
Silicon Laboratories Inc
![4463-TCE20C460-EK](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
I°/4463 20 DBM RFSWITCH RADIO TEST CARD 460 MHZ
Manufacturer:
Silicon Laboratories Inc
![4463-TCE20C868-EK](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
I°/4463 20 DBM RADIO TEST CARD 868 MHZ
Manufacturer:
Silicon Laboratories Inc
![4463-TCE27F868-EK](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
I°/4463 27 DBM RADIO TEST CARD 868 MHZ
Manufacturer:
Silicon Laboratories Inc
![4463-TCE30E915S-EK](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
I°/4463 SKYWORKS 30 DBM RADIO TEST CARD 915 MHZ
Manufacturer:
Silicon Laboratories Inc
![4463-TCE30E915R-EK](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
N/A N/A/-40 TO 85 OC/4463 RFMD 30 DBM RADIO TEST CARD 915 MHZ
Manufacturer:
Silicon Laboratories Inc
![4463-TSQ20D169-EK](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_tmb.jpg)
Part Number:
Description:
I°/4463 20 DBM RADIO TEST CARD 169 MHZ
Manufacturer:
Silicon Laboratories Inc