ATTINY20-EK1 Atmel, ATTINY20-EK1 Datasheet - Page 13

• Manufacturer Part Number: ATTINY20-EK1
• Description: KIT EVAL TOUCH ATTINY20
• Manufacturer: Atmel

Specifications of ATTINY20-EK1

• Sensor Type: *
• Sensing Range: *
• Interface: *
• Sensitivity: *
• Voltage - Supply: *
• Embedded: *
• Utilized Ic / Part: *
• Silicon Manufacturer: Atmel
• Core Architecture: AVR
• Core Sub-architecture: TinyAVR
• Kit Contents: Board
• Svhc: No SVHC (15-Dec-2010)
• Mcu Supported Families: ATtiny20
• Tool / Board Applications: Microcontroller
• Rohs Compliant: Yes
• Tool Type: Development Kit
• Cpu Core: AVR 8
• Data Bus Width: 8 bit
• Processor To Be Evaluated: ATtiny20
• Interface Type: Touch
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

4.8
4.8.1
4.8.2
8235B–AVR–04/11
Register Description
CCP – Configuration Change Protection Register
SPH and SPL — Stack Pointer Registers
• Bits 7:0 – CCP[7:0]: Configuration Change Protection
In order to change the contents of a protected I/O register the CCP register must first be written
with the correct signature. After CCP is written the protected I/O registers may be written to dur-
ing the next four CPU instruction cycles. All interrupts are ignored during these cycles. After
these cycles interrupts are automatically handled again by the CPU, and any pending interrupts
will be executed according to their priority.
When the protected I/O register signature is written, CCP0 will read as one as long as the pro-
tected feature is enabled, while CCP[7:1] will always read as zero.
Table 4-1
Table 4-1.
Notes:
• Bits 7:0 – SP[7:0]: Stack Pointer
The Stack Pointer register points to the top of the stack, which is implemented growing from
higher memory locations to lower memory locations. Hence, a stack PUSH command decreases
the stack pointer.
The stack space in the data SRAM must be defined by the program before any subroutine calls
are executed or interrupts are enabled.
In ATtiny20, the SPH register has not been implemented.
Bit
0x3C
Read/Write
Initial Value
Initial Value
Read/Write
Bit
0x3E
0x3D
Bit
Read/Write
Initial Value
Signature
0xD8
1. Only WDE and WDP[3:0] bits are protected in WDTCSR.
2. Only BODS bit is protected in MCUCR.
shows the signatures that are in recognised.
Signatures Recognised by the Configuration Change Protection Register
RAMEND
SP7
R/W
Group
IOREG: CLKMSR, CLKPSR, WDTCSR
W
7
0
15
R
0
–
7
RAMEND
SP6
R/W
W
6
0
14
R
0
–
6
RAMEND
SP5
R/W
W
5
0
13
R
0
–
5
RAMEND
SP4
R/W
W
4
0
12
R
0
–
4
CCP[7:0]
RAMEND
(1)
SP3
R/W
W
3
0
11
, MCUCR
R
–
3
0
RAMEND
SP2
R/W
W
(2)
2
0
10
R
2
0
–
Description
Protected I/O register
RAMEND
SP1
R/W
W
1
0
R
9
1
0
–
ATtiny20
RAMEND
R/W
R/W
SP0
0
0
R
8
0
0
–
CCP
SPH
SPL
13