ADC08D1500DEV/NOPB National Semiconductor, ADC08D1500DEV/NOPB Datasheet - Page 6

• Manufacturer Part Number: ADC08D1500DEV/NOPB
• Description: BOARD DEV FOR ADC08D1500
• Manufacturer: National Semiconductor
• Series: PowerWise®r

Specifications of ADC08D1500DEV/NOPB

• Mfg Application Notes: Clocking High-Speed A/D Converters AppNote
• Number Of Adc's: 2
• Number Of Bits: 8
• Sampling Rate (per Second): 1.5G
• Data Interface: Serial
• Inputs Per Adc: 1 Differential
• Input Range: 870 mVpp
• Power (typ) @ Conditions: 1.8W @ 1.5GSPS
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 85°C
• Utilized Ic / Part: ADC08D1500
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: ADC08D1500DEV

www.national.com
Pin Functions
2, 5, 8, 13,
16, 17, 20,
25, 28, 33,
40, 51 ,62,
73, 88, 99,
1, 6, 9, 12,
21, 24, 27,
110, 121
100 / 61
101 / 60
102 / 59
103 / 58
104 / 57
105 / 56
106 / 55
107 / 54
111 / 50
112 / 49
113 / 48
114 / 47
115 / 46
116 / 45
117 / 44
118 / 43
122 / 39
123 / 38
124 / 37
125 / 36
Pin No.
83 / 78
84 / 77
85 / 76
86 / 75
89 / 72
90 / 71
91 / 70
92 / 69
93 / 68
94 / 67
95 / 66
96 / 65
128
79
80
82
81
41
DId7− / DQd7−
DId7+ / DQd7+
DId6− / DQd6−
DId6+ / DQd6+
DId5− / DQd5−
DId5+ / DQd5+
DId4− / DQd4−
DId4+ / DQd4+
DId3− / DQd3−
DId3+ / DQd3+
DId2− / DQd2−
DId2+ / DQd2+
DId1− / DQd1−
DId1+ / DQd1+
DId0− / DQd0−
DId0+ / DQd0+
DI7− / DQ7−
DI7+ / DQ7+
DI6− / DQ6−
DI6+ / DQ6+
DI5− / DQ5−
DI5+ / DQ5+
DI4− / DQ4−
DI4+ / DQ4+
DI3− / DQ3−
DI3+ / DQ3+
DI2− / DQ2−
DI2+ / DQ2+
DI1− / DQ1−
DI1+ / DQ1+
DI0− / DQ0−
DI0+ / DQ0+
Symbol
DCLK+
DCLK-
GND
OR+
OR-
V
V
DR
A
Equivalent Circuit
6
I and Q channel LVDS Data Outputs that are not delayed in the
output demultiplexer. Compared with the DId and DQd outputs,
these outputs represent the later time samples. These outputs
should always be terminated with a 100Ω differential resistor.
I and Q channel LVDS Data Outputs that are delayed by one CLK
cycle in the output demultiplexer. Compared with the DI/DQ
outputs, these outputs represent the earlier time sample. These
outputs should always be terminated with a 100Ω differential
resistor.
Out Of Range output. A differential high at these pins indicates that
the differential input is out of range (outside the range ±V
programmed by the FSR pin in non-extended control mode or the
Input Full-Scale Voltage Adjust register setting in the extended
control mode).
Differential Clock outputs used to latch the output data. Delayed
and non-delayed data outputs are supplied synchronous to this
signal. This signal is at 1/2 the input clock rate in SDR mode and
at 1/4 the input clock rate in the DDR mode. The DCLK outputs
are not active during a calibration cycle, therefore this is not
recommended as a system clock.
Analog power supply pins. Bypass these pins to ground.
Output Driver power supply pins. Bypass these pins to DR GND.
Ground return for V
A
.
Description
IN
/2 as