LPC1313FHN33/01,51 NXP Semiconductors, LPC1313FHN33/01,51 Datasheet - Page 2

• Manufacturer Part Number: LPC1313FHN33/01,51
• Description: ARM Microcontrollers - MCU CortexM3 32bit 32KB
• Manufacturer: NXP Semiconductors

Specifications of LPC1313FHN33/01,51

• Rohs: yes
• Core: ARM Cortex M3
• Processor Series: LPC1313
• Data Bus Width: 32 bit
• Maximum Clock Frequency: 72 MHz
• Program Memory Size: 32 KB
• Data Ram Size: 8 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 2 V to 3.6 V
• Package / Case: HVQFN-33
• Mounting Style: SMD/SMT
• Factory Pack Quantity: 4000

NXP Semiconductors
LPC1311_13_42_43
Product data sheet





















Serial interfaces:
Other peripherals:
Serial Wire Debug and Serial Wire Trace port.
High-current output driver (20 mA) on one pin.
High-current sink drivers (20 mA) on two I
Integrated PMU (Power Management Unit) to minimize power consumption during
Sleep, Deep-sleep, and Deep power-down modes.
Power profiles residing in boot ROM allowing to optimize performance and minimize
power consumption for any given application through one simple function call.
(LPC1300L series, on LPC1311/01 and LPC1313/01 only.)
Three reduced power modes: Sleep, Deep-sleep, and Deep power-down.
Single power supply (2.0 V to 3.6 V).
10-bit ADC with input multiplexing among 8 pins.
GPIO pins can be used as edge and level sensitive interrupt sources.
Clock output function with divider that can reflect the system oscillator clock, IRC
clock, CPU clock, or the watchdog clock.
Processor wake-up from Deep-sleep mode via a dedicated start logic using up to 40 of
the functional pins.
Brownout detect with four separate thresholds for interrupt and one threshold for
forced reset (four thresholds for forced reset on the LPC1311/01 and LPC1313/01
parts).
Power-On Reset (POR).
Integrated oscillator with an operating range of 1 MHz to 25 MHz.
12 MHz internal RC oscillator trimmed to 1 % accuracy over the entire temperature
and voltage range that can optionally be used as a system clock.
Programmable watchdog oscillator with a frequency range of 7.8 kHz to 1.8 MHz.
System PLL allows CPU operation up to the maximum CPU rate without the need for a
high-frequency crystal. May be run from the system oscillator or the internal RC
oscillator.
For USB (LPC1342/43), a second, dedicated PLL is provided.
Code Read Protection (CRP) with different security levels.










USB 2.0 full-speed device controller with on-chip PHY for device (LPC1342/43
only).
UART with fractional baud rate generation, modem, internal FIFO, and
RS-485/EIA-485 support.
SSP controller with FIFO and multi-protocol capabilities.
Additional SSP controller on LPC1313FBD48/01.
I
data rate of 1 Mbit/s with multiple address recognition and monitor mode.
Up to 42 General Purpose I/O (GPIO) pins with configurable pull-up/pull-down
resistors.
Four general purpose counter/timers with a total of four capture inputs and 13
match outputs.
Programmable WatchDog Timer (WDT).
Programmable Windowed Watchdog Timer (WWDT) on LPC1311/01 and
LPC1313/01.
System tick timer.
2
C-bus interface supporting full I
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 6 June 2012
2
C-bus specification and Fast-mode Plus with a
2
C-bus pins in Fast-mode Plus.
32-bit ARM Cortex-M3 microcontroller
LPC1311/13/42/43
© NXP B.V. 2012. All rights reserved.
2 of 74