LPC1313FHN33/01,51 NXP Semiconductors, LPC1313FHN33/01,51 Datasheet - Page 13

• Manufacturer Part Number: LPC1313FHN33/01,51
• Description: ARM Microcontrollers - MCU CortexM3 32bit 32KB
• Manufacturer: NXP Semiconductors

Specifications of LPC1313FHN33/01,51

• Rohs: yes
• Core: ARM Cortex M3
• Processor Series: LPC1313
• Data Bus Width: 32 bit
• Maximum Clock Frequency: 72 MHz
• Program Memory Size: 32 KB
• Data Ram Size: 8 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 2 V to 3.6 V
• Package / Case: HVQFN-33
• Mounting Style: SMD/SMT
• Factory Pack Quantity: 4000

NXP Semiconductors
Table 3.
[1]
[3]
[4]
[5]
LPC1311_13_42_43
Product data sheet
[2]
[6]
[7]
Symbol
PIO2_10
PIO2_11/SCK0
PIO3_0/DTR
PIO3_1/DSR
PIO3_2/DCD
PIO3_3/RI
PIO3_4
PIO3_5
USB_DM
USB_DP
V
XTALIN
XTALOUT
V
DD
SS
Pin state at reset for default function: I = Input; O = Output; PU = internal pull-up enabled (for V
parts LPC1311/13/42/43 and pulled up to 3.3 V for parts LPC1311/01 and LPC1313/01); IA = inactive, no pull-up/down enabled;
F = floating; floating pins, if not used, should be tied to ground or power to minimize power consumption.
5 V tolerant pad. See
WAKEUP pin to reset the chip and wake up from Deep power-down mode. An external pull-up resistor is required on this pin for the
Deep power-down mode.
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors and configurable hysteresis (see
I
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors, configurable hysteresis, and analog input.
When configured as a ADC input, digital section of the pad is disabled and the pin is not 5 V tolerant (see
Pad provides USB functions. It is designed in accordance with the USB specification, revision 2.0 (Full-speed and Low-speed mode
only). This pad is not 5 V tolerant.
When the system oscillator is not used, connect XTALIN and XTALOUT as follows: XTALIN can be left floating or can be grounded
(grounding is preferred to reduce susceptibility to noise). XTALOUT should be left floating.
2
C-bus pads compliant with the I
LPC1313/42/43 LQFP48 pin description table
Figure 37
Pin
25
31
36
37
43
48
18
21
19
20
8;
44
6
7
5;
41
[7]
[7]
[3]
[3]
[3]
[3]
[3]
[3]
[3]
[3]
[6]
[6]
Start
logic
input
yes
yes
yes
yes
yes
yes
no
no
no
no
-
-
-
-
for pad characteristics. RESET functionality is not available in Deep power-down mode. Use the
2
C-bus specification for I
Type Reset
I/O
I/O
I/O
I/O
O
I/O
I
I/O
I
I/O
I
I/O
I/O
I/O
I/O
I
I
O
I
All information provided in this document is subject to legal disclaimers.
state
[1]
I; PU
I; PU
-
I; PU
-
I; PU
-
I; PU
-
I; PU
-
I; PU
I; PU
F
F
-
-
-
-
Rev. 5 — 6 June 2012
Description
PIO2_10 — General purpose digital input/output pin.
PIO2_11 — General purpose digital input/output pin.
SCK0 — Serial clock for SSP0.
PIO3_0 — General purpose digital input/output pin.
DTR — Data Terminal Ready output for UART (LPC1311/01 and
LPC1313/01 only).
PIO3_1 — General purpose digital input/output pin.
DSR — Data Set Ready input for UART (LPC1311/01 and
LPC1313/01 only).
PIO3_2 — General purpose digital input/output pin.
DCD — Data Carrier Detect input for UART (LPC1311/01 and
LPC1313/01 only).
PIO3_3 — General purpose digital input/output pin.
RI — Ring Indicator input for UART (LPC1311/01 and LPC1313/01
only).
PIO3_4 — General purpose digital input/output pin (LPC1313 only).
PIO3_5 — General purpose digital input/output pin (LPC1313 only).
USB_DM — USB bidirectional D− line (LPC1342/43 only).
USB_DP — USB bidirectional D+ line (LPC1342/43 only).
3.3 V supply voltage to the internal regulator, the external rail, and
the ADC. Also used as the ADC reference voltage.
Input to the oscillator circuit and internal clock generator circuits.
Input voltage must not exceed 1.8 V.
Output from the oscillator amplifier.
Ground.
2
C standard mode and I
…continued
2
C Fast-mode Plus.
32-bit ARM Cortex-M3 microcontroller
LPC1311/13/42/43
DD
= 3.3 V, pin is pulled up to 2.6 V for
Figure
© NXP B.V. 2012. All rights reserved.
36).
Figure
13 of 74
36).