LPC1313FHN33/01,51 NXP Semiconductors, LPC1313FHN33/01,51 Datasheet - Page 16

• Manufacturer Part Number: LPC1313FHN33/01,51
• Description: ARM Microcontrollers - MCU CortexM3 32bit 32KB
• Manufacturer: NXP Semiconductors

Specifications of LPC1313FHN33/01,51

• Rohs: yes
• Core: ARM Cortex M3
• Processor Series: LPC1313
• Data Bus Width: 32 bit
• Maximum Clock Frequency: 72 MHz
• Program Memory Size: 32 KB
• Data Ram Size: 8 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 2 V to 3.6 V
• Package / Case: HVQFN-33
• Mounting Style: SMD/SMT
• Factory Pack Quantity: 4000

NXP Semiconductors
Table 4.
[1]
[3]
[4]
[5]
LPC1311_13_42_43
Product data sheet
[2]
[6]
[7]
Symbol
PIO1_7/TXD/
CT32B0_MAT1
PIO1_8/
CT16B1_CAP0
PIO1_9/
CT16B1_MAT0
PIO1_10/AD6/
CT16B1_MAT1
PIO1_11/AD7
PIO2_0/DTR
PIO3_2
PIO3_4
PIO3_5
USB_DM
USB_DP
V
XTALIN
XTALOUT
V
DD
SS
Pin state at reset for default function: I = Input; O = Output; PU = internal pull-up enabled (for V
parts LPC1311/13/42/43 and pulled up to 3.3 V for parts LPC1311/01 and LPC1313/01); IA = inactive, no pull-up/down enabled.
F = floating; floating pins, if not used, should be tied to ground or power to minimize power consumption.
5 V tolerant pad. See
WAKEUP pin to reset the chip and wake up from Deep power-down mode. An external pull-up resistor is required on this pin for the
Deep power-down mode.
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors and configurable hysteresis (see
I
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors, configurable hysteresis, and analog input.
When configured as a ADC input, digital section of the pad is disabled, and the pin is not 5 V tolerant (see
Pad provides USB functions. It is designed in accordance with the USB specification, revision 2.0 (Full-speed and Low-speed mode
only). This pad is not 5 V tolerant.
When the system oscillator is not used, connect XTALIN and XTALOUT as follows: XTALIN can be left floating or can be grounded
(grounding is preferred to reduce susceptibility to noise). XTALOUT should be left floating.
2
C-bus pads compliant with the I
LPC1311/13/42/43 HVQFN33 pin description table
Pin
32
7
12
20
27
1
28
13
14
13
14
6;
29
4
5
33
[3]
[3]
[7]
[7]
Figure 37
[3]
[3]
[5]
[5]
[3]
[3]
[3]
[6]
[6]
Start
logic
input
yes
yes
yes
yes
yes
yes
yes
no
no
no
no
-
-
-
-
for pad characteristics. RESET functionality is not available in Deep power-down mode. Use the
2
C-bus specification for I
Type Reset
O
O
I
O
I
O
I
O
I/O
I/O
I/O
I/O
I
I
O
-
I/O
I/O
I/O
I/O
I/O
I/O
I/O
All information provided in this document is subject to legal disclaimers.
state
[1]
I; PU
-
-
I; PU
-
I; PU
-
I; PU
-
-
I; PU
-
I; PU
-
I; PU
I; PU
I; PU
F
F
-
-
-
-
CT16B1_MAT1 — Match output 1 for 16-bit timer 1.
Description
PIO1_7 — General purpose digital input/output pin.
TXD — Transmitter output for UART.
CT32B0_MAT1 — Match output 1 for 32-bit timer 0.
PIO1_8 — General purpose digital input/output pin.
CT16B1_CAP0 — Capture input 0 for 16-bit timer 1.
PIO1_9 — General purpose digital input/output pin.
CT16B1_MAT0 — Match output 0 for 16-bit timer 1.
PIO1_10 — General purpose digital input/output pin.
AD6 — A/D converter, input 6.
PIO1_11 — General purpose digital input/output pin.
AD7 — A/D converter, input 7.
PIO2_0 — General purpose digital input/output pin.
DTR — Data Terminal Ready output for UART.
PIO3_2 — General purpose digital input/output pin.
PIO3_4 — General purpose digital input/output pin (LPC1311/13 only).
PIO3_5 — General purpose digital input/output pin (LPC1311/13 only).
USB_DM — USB bidirectional D− line (LPC1342/43 only).
USB_DP — USB bidirectional D+ line (LPC1342/43 only).
3.3 V supply voltage to the internal regulator, the external rail, and the
ADC. Also used as the ADC reference voltage.
Input to the oscillator circuit and internal clock generator circuits. Input
voltage must not exceed 1.8 V.
Output from the oscillator amplifier.
Thermal pad. Connect to ground.
Rev. 5 — 6 June 2012
2
C standard mode and I
…continued
2
C Fast-mode Plus.
32-bit ARM Cortex-M3 microcontroller
LPC1311/13/42/43
DD
= 3.3 V, pin is pulled up to 2.6 V for
Figure
© NXP B.V. 2012. All rights reserved.
36).
Figure
16 of 74
36).