AM49BDS640AHD8I SPANSION [SPANSION], AM49BDS640AHD8I Datasheet - Page 45
![no-image](/images/no-image-200.jpg)
AM49BDS640AHD8I
Manufacturer Part Number
AM49BDS640AHD8I
Description
Stacked Multichip Package (MCP), Flash Memory and pSRAM CMOS 1.8 Volt-only Simultaneous Read/Write
Manufacturer
SPANSION [SPANSION]
Datasheet
1.AM49BDS640AHD8I.pdf
(84 pages)
- Current page: 45 of 84
- Download datasheet (2Mb)
DQ3: Sector Erase Timer
After writing a sector erase command sequence, the
system may read DQ3 to determine whether or not
erasure has begun. (The sector erase timer does not
apply to the chip erase command.) If additional sectors
are selected for erasure, the entire time-out also
applies after each additional sector erase command.
When the time-out period is complete, DQ3 switches
from a “0” to a “1.” If the time between additional sector
erase commands from the system can be assumed to
be less than 50 µs, the system need not monitor DQ3.
See also
page
Notes:
1. DQ5 switches to ‘1’ when an Embedded Program or Embedded Erase operation has exceeded the maximum timing limits.
2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further details.
3. When reading write operation status bits, the system must always provide the bank address where the Embedded Algorithm
4. The system may read either asynchronously or synchronously (burst) while in erase suspend.
5. The RDY pin acts a dedicated output to indicate the status of an embedded erase or program operation is in progress. This
December 5, 2003
Standard
Suspend
Refer to the section on DQ5 for more information.
is in progress. The device outputs array data if the system addresses a non-busy bank.
is available in the Asynchronous mode only.
Mode
Erase
Mode
31.
“Sector Erase Command Sequence” on
Embedded Program Algorithm
Embedded Erase Algorithm
Erase-Suspend-Program
Erase-Suspend-
Read (Note 4)
Status
Erase
Suspended Sector
Non-Erase
Suspended Sector
A D V A N C E
Table 17. Write Operation Status
Am49BDS640AH
(Note 2)
DQ7#
DQ7#
Data
DQ7
I N F O R M A T I O N
0
1
After the sector erase command is written, the system
should read the status of DQ7 (Data# Polling) or DQ6
(Toggle Bit I) to ensure that the device has accepted
the command sequence, and then read DQ3. If DQ3 is
“1,” the Embedded Erase algorithm has begun; all
further commands (except Erase Suspend) are ignored
until the erase operation is complete. If DQ3 is “0,” the
device will accept additional sector erase commands.
To ensure the command has been accepted, the
system software should check the status of DQ3 prior
to and following each subsequent sector erase com-
mand. If DQ3 is high on the second status check, the
last command might not have been accepted.
Table 17
status bits.
No toggle
Toggle
Toggle
Toggle
Data
DQ6
shows the status of DQ3 relative to the other
(Note 1)
Data
DQ5
0
0
0
0
Data
DQ3
N/A
N/A
N/A
1
No toggle
(Note 2)
Toggle
Toggle
DQ2
Data
N/A
Impedance
Impedance
RDY (Note
High
High
5)
0
0
0
43
Related parts for AM49BDS640AHD8I
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![S34ML01G100TFI000](/images/no-image3.png)
Part Number:
Description:
TS 48/CIVIL/1-BIT ECC, X8 I/O AND 3V VCC SPANSION SLC NAND
Manufacturer:
SPANSION
Datasheet:
![S34ML04G100TFI000](/images/no-image3.png)
Part Number:
Description:
TS 48/CIVIL/1-BIT ECC, X8 I/O AND 3V VCC SPANSION SLC NAND
Manufacturer:
SPANSION
Datasheet:
![AM29F010B-70EC](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
![AM29DL322GT70WMI](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
![AM29DL323GB90WMI](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
![MBM29F400TC-70PFTN](/images/no-image3.png)
Part Number:
Description:
MBM29F400TC-70PFTNSPANSION [FLASH MEMORY CMOS 4M (512K x 8/256K x 16) BIT]
Manufacturer:
SPANSION
Datasheet:
![AM29F010B70JI](/images/no-image3.png)
Part Number:
Description:
AM29F010B70JI1 Megabit (128 K x 8-bit) CMOS 5.0 Volt-only, Uniform Sector Flash Memory
Manufacturer:
SPANSION
Datasheet:
![S29AL016D70BAI020](/images/no-image3.png)
Part Number:
Description:
S29AL016D70BAI02016 MEGABIT CMOS 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
Manufacturer:
SPANSION
Datasheet:
![S29AL016M90FAI010](/images/no-image3.png)
Part Number:
Description:
S29AL016M90FAI01016 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
Manufacturer:
SPANSION
Datasheet:
![S29AL016M90FAI020](/images/no-image3.png)
Part Number:
Description:
S29AL016M90FAI02016 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
Manufacturer:
SPANSION
Datasheet:
![AM49LV128BMH15NT](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
![AM49PDL127BH](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
![MBM29DL800TA-90PFTN](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
![MBM29DL800BA-90PFTN](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
![AM29F010B-90JI](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet: