Z8F082A28100KIT ZILOG [Zilog, Inc.], Z8F082A28100KIT Datasheet - Page 134
![no-image](/images/no-image-200.jpg)
Z8F082A28100KIT
Manufacturer Part Number
Z8F082A28100KIT
Description
Z8 Encore XP-R F08xA Series with eXtended Peripherals
Manufacturer
ZILOG [Zilog, Inc.]
Datasheet
1.Z8F082A28100KIT.pdf
(244 pages)
- Current page: 134 of 244
- Download datasheet (3Mb)
®
Z8 Encore! XP
F08xA Series
Product Specification
116
Transimpedance Amplifier
The transimpedance amplifier is a standard operational amplifier designed for current
measurements. Each of the three ports of the amplifier is accessible from the package pins.
The inverting input is commonly used to connect to the current source. The output node
connects an external feedback network to the inverting input. The non-inverting output is
required to apply a non-zero bias point. In a standard, single-supply system, this bias point
must be substantially above ground to measure positive input currents. The non-inverting
input may also be used for offset correction.
The transimpedance amplifier contains only one pin configuration: ANA0 is the output/
feedback node, ANA1 is the inverting input and ANA2 is the non-inverting input.
To use the transimpedance amplifier, it must be enabled in the
Power Control Register 0
. The default state of the transimpedance amplifier is OFF. To use the transim-
(PWRCTL0)
pedance amplifier, the TRAM bit must be cleared, turning it ON (
“Power Control Register
). When making normal ADC measurements on ANA0 (not tran-
0 (PWRCTL0)” on page 30
simpedance measurements), the TRAM bit must be OFF. Turning the TRAM bit ON inter-
feres with normal ADC measurements. Finally, this bit enables the amplifier even in
STOP mode. If the amplifier is not required in STOP mode, disable it. Failing to perform
this results in STOP mode currents greater than specified.
As with other ADC measurements, any pins used for analog purposes must be configured
as such in the GPIO registers (see
“Port A–D Alternate Function Sub-Registers” on
).
page 39
Standard transimpedance measurements are made on ANA0, as selected by the
ANAIN[3:0] bits of
. It is also possible to make single-ended mea-
ADC Control Register 0
surements on ANA1 and ANA2 while the amplifier is enabled, which is often useful for
determining offset conditions.
The
[2:0] bits of
must also be configured for sin-
ADC Control/Status Register 1
BUFFMODE
gle-ended, unity-gain buffered operation. Using the transimpedance amplifier in an unbuf-
fered or differential mode is not recommended.
When either input is overdriven, the amplifier output saturates at the positive or negative
supply voltage. No instability results.
PS024705-0405
P R E L I M I N A R Y
Analog-to-Digital Converter
Related parts for Z8F082A28100KIT
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![Z8018218FSC](/images/manufacturer_photos/0/7/730/zilog__inc__tmb.jpg)
Part Number:
Description:
Communication Controllers, ZILOG INTELLIGENT PERIPHERAL CONTROLLER (ZIP)
Manufacturer:
Zilog, Inc.
Datasheet:
![Z86C6116FSC](/images/manufacturer_photos/0/7/730/zilog__inc__tmb.jpg)
Part Number:
Description:
CMOS Z8 microcontroller. ROM 16 Kbytes, RAM 256 bytes, speed 16 MHz, 32 lines I/O, 3.0V to 5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
![Z86E0208PSC](/images/manufacturer_photos/0/7/730/zilog__inc__tmb.jpg)
Part Number:
Description:
Low-cost microcontroller. 512 bytes ROM, 61 bytes RAM, 8 MHz
Manufacturer:
Zilog, Inc.
Datasheet:
![Z86E40](/images/manufacturer_photos/0/7/730/zilog__inc__tmb.jpg)
Part Number:
Description:
Z8 4K OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
![Z88C0020VEC](/images/manufacturer_photos/0/7/730/zilog__inc__tmb.jpg)
Part Number:
Description:
CMOS SUPER8 ROMLESS MCU
Manufacturer:
Zilog, Inc.
Datasheet:
![Z86E0812SSC](/images/manufacturer_photos/0/7/730/zilog__inc__tmb.jpg)
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
![Z86E0812PSC](/images/manufacturer_photos/0/7/730/zilog__inc__tmb.jpg)
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
![Z86E0412PSC](/images/manufacturer_photos/0/7/730/zilog__inc__tmb.jpg)
Part Number:
Description:
OTP (KB) = 1, RAM = 125, Speed = 12, I/O = 14, 8-bit Timers = 2, Comm Interfaces Other Features = Por, LV Protect, Voltage = 4.5-5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
![Z9023306PSC](/images/manufacturer_photos/0/7/730/zilog__inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Zilog, Inc.
Datasheet:
![Z86C1505PSC](/images/manufacturer_photos/0/7/730/zilog__inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Zilog, Inc.
Datasheet:
![Z86C3312PSC](/images/manufacturer_photos/0/7/730/zilog__inc__tmb.jpg)
Part Number:
Description:
CMOS Z8 consumer controller processor. ROM 4 KB, RAM 237 bytes, speed 12 MHz, 24 lines I/O, 3.0V to 5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
![Z86C4316PSC](/images/manufacturer_photos/0/7/730/zilog__inc__tmb.jpg)
Part Number:
Description:
CMOS Z8 consumer controller processor. ROM 4 KB, RAM 236 bytes, speed 16 MHz, 32 lines I/O, 3.0V to 5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
![Z86C4312VSC](/images/manufacturer_photos/0/7/730/zilog__inc__tmb.jpg)
Part Number:
Description:
CMOS Z8 consumer controller processor. ROM 4 KB, RAM 236 bytes, speed 12 MHz, 32 lines I/O, 3.0V to 5.5V
Manufacturer:
Zilog, Inc.
Datasheet: