MC68HC908KX2 MOTOROLA [Motorola, Inc], MC68HC908KX2 Datasheet - Page 118
MC68HC908KX2
Manufacturer Part Number
MC68HC908KX2
Description
Microcontrollers
Manufacturer
MOTOROLA [Motorola, Inc]
Datasheet
1.MC68HC908KX2.pdf
(311 pages)
- Current page: 118 of 311
- Download datasheet (2Mb)
Internal Clock Generator Module (ICG)
7.5.3 Using Clock Monitor Interrupts
Technical Data
118
The clock monitor circuit can be used to recover from perilous situations
such as crystal loss. To use the clock monitor effectively, these points
should be observed:
•
•
•
•
•
•
•
•
•
Enable the clock monitor and clock monitor interrupts.
The first statement in the clock monitor interrupt service routine
(CMISR) should be a read to the ICG control register (ICGCR) to
verify that the clock monitor flag (CMF) is set. This is also the first
step in clearing the CMF bit.
The second statement in the CMISR should be a write to the
ICGCR to clear the CMF bit (write the bit low). Writing the bit high
will not affect it. This statement does not need to immediately
follow the first, but must be contained in the CMISR.
The third statement in the CMISR should be to clear the CMON bit.
This is required to ensure proper reconfiguration of the reference
dividers. This statement also must be contained in the CMISR.
Although the clock monitor can be enabled only when both clocks
are stable (ICGS is set or ECGS is set), it will remain set if one of
the clocks goes unstable.
The clock monitor only works if the external slow (EXTSLOW) bit
in the CONFIG or MOR is set to the correct value.
The internal and external clocks must both be enabled and
running to use the clock monitor.
When the clock monitor detects inactivity, the inactive clock is
automatically deselected and the active clock selected as the
source for CGMXCLK and TBMCLK. The CMISR can use the
state of the CS bit to check which clock is inactive.
When the clock monitor detects inactivity, the application may
have been subjected to extreme conditions which may have
affected other circuits. The CMISR should take any appropriate
precautions.
Internal Clock Generator Module (ICG)
MC68HC908KX8 • MC68HC908KX2 • MC68HC08KX8 — Rev. 1.0
MOTOROLA
Related parts for MC68HC908KX2
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Motorola, Inc [VOLTAGE REGULATOR]
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
6367254 MOTOROLA SC (XSTRS/R F)
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
MC1494LMotorola, Inc [MONOLITHIC FOUR-QUADRANT MULTIPLIER]
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
MC1466LMotorola, Inc [PRECISION WIDE RANGE VOLTAGE AND CURRENT REGULATOR]
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
MC145532DWMotorola, Inc [ADPCM Transcoder]
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
Silicon Controlled Rectifiers
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
RF Power Field Effect Transistors N-Channel Enhancement-Mode Lateral MOSFETs
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
RF POWER FIELD EFFECT TRANSISTORS
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
LATERAL N-CHANNEL BROADBAND RF POWER MOSFETs
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
RF POWER FIELD EFFECT TRANSISTOR
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
RF LOW POWER TRANSISTOR NPN SILICON
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
PLASTIC SURFACE MOUNT ZENER DIODES 1.5 WATTS 3.3-68 VOLTS
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
OVERVOLTAGE TRANSIENT SUPPRESSOR
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
TMOS POWER FET 15 AMPERES 60 VOLTS
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
TMOS POWER FET LOGIC LEVEL 19 AMPERES 30 VOLTS RDS(on) = 0.099 OHM
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet: