pi7c8154a Pericom Semiconductor Corporation, pi7c8154a Datasheet - Page 69
![no-image](/images/no-image-200.jpg)
pi7c8154a
Manufacturer Part Number
pi7c8154a
Description
2-port Pci-to-pci Bridge
Manufacturer
Pericom Semiconductor Corporation
Datasheet
1.PI7C8154A.pdf
(112 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
pi7c8154aNAE
Manufacturer:
XILINX
Quantity:
192
Table 8-1 GPIO OPERATION
The data is input through the dedicated input signal, MSK_IN.
The shift register circuitry is not necessary for correct operation of PI7C8154A. The shift register
can be eliminated, and MSK_IN can be tied LOW to enable all secondary clock outputs or tied
HIGH to force all secondary clock outputs HIGH. Table 8-2 shows the format of the serial stream.
Table 8-2 GPIO SERIAL DATA FORMAT
The first 8 bits contain the PRSNT#[1:0] signal values for four slots, and these bits control the
S_CLKOUT[3:0] outputs. If one or both of the PRSNT#[1:0] signals are 0, that indicates that a
card is present in the slot and therefore the secondary clock for that slot is not masked. If these
clocks are connected to devices and not to slots, one or both of the bits should be tied low to enable
the clock.
The next 5 bits are the clock mask for devices; each bit enables or disables the clock for one device.
These bits control the S_CLKOUT[8:4] outputs: 0 enables the clock, and 1 disables the clock.
Bit 13 is the clock enable bit for S_CLKOUT[9], which is connected to PI7C8154A’s S_CLKIN
input.
If desired, the assignment of S_CLKOUT outputs to slots, devices, and PI7C8154A’s S_CLKIN
input can be rearranged from the assignment shown here. However, it is important that the serial
data stream format match the assignment of S_CLKOUT.
The 8 least significant bits are connected to the PRSNT# pins for the slots. The next 5 bits are tied
high to disable their respective secondary clocks because those clocks are not connected to
anything. The next bit is tied LOW because that secondary clock output is connected to the bridge
S_CLKIN input. When the secondary reset signal, S_RESET#, is detected asserted and the primary
reset signal, P_RESET#, is detected deasserted, the bridge drives GPIO[2] LOW for one cycle to
load the clock mask inputs into the shift register. On the next cycle, PI7C8154A drives GPIO[2]
HIGH to perform a shift operation. This shifts the clock mask into MSK_IN; the most significant
bit is shifted in first, and the least significant bit is shifted in last.
GPIO[0]
GPIO[1]
GPIO[2]
GPIO[3]
[1:0]
[3:2]
[5:4]
[7:6]
[10]
[11]
[12]
[13]
[14]
[15]
Bit
[8]
[9]
GPIO Pin
Slot 0 PRSNT#[1:0] or device 0
Slot 1 PRSNT#[1:0] or device 1
Slot 2 PRSNT#[1:0] or device 2
Slot 3 PRSNT#[1:0] or device 3
Device 4
Device 5
Device 6
Device 7
Device 8
PI7C8154A S_CLKIN
Reserved
Reserved
Page 69 of 112
Description
Shift register clock output at 33MHz max frequency
Not used
Shift register control
0: Load
1: Shift
Not used
Operation
ASYNCHRONOUS 2-PORT
JULY 2004 REVISION 1.00
PCI-to-PCI BRIDGE
Advance Information
S_CLKOUT
NA
NA
0
1
2
3
4
5
6
7
8
9
PI7C8154A