MAXQ3108 Maxim Integrated Products, MAXQ3108 Datasheet - Page 48

• Manufacturer Part Number: MAXQ3108
• Description: Dual-Core Microcontroller
• Manufacturer: Maxim Integrated Products

www.DataSheet4U.com
Low-Power, Dual-Core Microcontroller
48
I2CCN (0Ch, 04h)
Initialization:
Read/Write Access:
I2CCN.0: I2CEN
I2CCN.1: I2CMST
I2CCN.2: I2CMODE
I2CCN.3: Reserved
I2CCN.4: I2CSTRS
I2CCN.5: I2CACK
I2CCN.6: I2CSTART
______________________________________________________________________________________
I
This register is cleared to 0000h on all forms of reset. The I2CSTART and I2CSTOP bits are reset to
0 when I2CMST = 0 or when I2CEN = 0. I2CSTART and I2CSTOP are mutually exclusive
operations. User software can only set one of these bits at any given time. I2CRST is reset to 0
when I2CEN = 0.
Unrestricted read. Unrestricted write access when I2CBUSY = 0. Writes to I2CMST, I2CMODE are
ignored when I2CBUSY = 1. Writes to I2CEN are normally disabled when I2CBUSY = 1. However,
when I2CRST = 1, I2CEN can be written to even when I2CBUSY = 1. Writes to I2CACK are ignored
when I2CRST = 1.
I
enabled. When cleared to 0, the I
I
module. When the I2CMST bit is set to 1, the I 2 C operates as a master. When the I2CMST is
cleared to 0, the I
the I
receives a general call (I2CGCI = 1).
I
master. When the I2CMODE bit is set to 1, the master is operating in receiver mode (reading from
slave). When the I2CMODE bit is cleared to 0, the master is operating in transmitter mode (writing
to slave). Note that software writing to this bit is prohibited in slave mode. When operating in
master mode, software configures this bit to the desired direction of data transfer. When operating
in slave mode, the direction of data transfer is determined by the R/W bit received during the
address stage and this bit reflects the actual R/W bit value in the current transfer and is set by
hardware. Software writing to this bit in slave mode is ignored.
Reserved. Do not write a 1 to this location. Functionally, this is the I2CEA bit, however, there are
problems with the I
I
8th clock cycle. Clearing this bit to 0 enables clock stretching after the falling edge of the 9th
clock cycle. This bit has no effect when clock stretching is disabled (I2CSTREN = 0).
I
acting as a receiver. Setting this bit to 1 generates a NACK (leaving SDA high). Clearing the
I2CACK bit to 0 generates an ACK (pulling SDA LOW) during the acknowledgement cycle. This bit
retains its value unless changed by software or hardware. When an I
(I2CRST = 1), this bit is set to 1 by hardware and software writes to this bit are ignored when
I2CRST = 1.
I
or generates a repeated START condition during a transfer where the I
master. This bit is automatically self-cleared to 0 after the START condition has been generated. If
the I
In master mode, setting this bit could also start the timeout timer if enabled. If the timeout timer
expires before the START condition can be generated, a timeout interrupt is generated to the CPU if
enabled. The I2CSTART bit is also cleared to 0 by the timeout event.
Note that this bit has no effect when the I
to 0 when I2CMST = 0 or I2CEN = 0. Also, the I2CSTART and I2CSTOP are mutually exclusive. If
both bits are set at the same time, it is considered as an invalid operation and the I
ignores the request and resets both bits to 0. Setting the I2CSTART bit to 1 while I2CSTOP = 1 is an
invalid operation and is ignored, leaving the I2CSTART bit cleared to 0.
2
2
2
2
2
2
2
C START Enable. Setting this bit automatically generates a START condition when the bus is free
C Control Register (16-Bit Register)
C Enable. This bit enables the I
C Master Mode Enable. The I2CMST bit functions as a master mode enable bit for the I
C Transfer Mode. The transfer mode bit selects the direction of data transfer with respect to the
C Clock Stretch Select. Setting this bit to 1 enables clock stretching after the falling edge of the
C Data Acknowledge Bit. This bit selects the acknowledge bit returned by the I
Special Function Register Bit Descriptions (continued)
2
2
C START interrupt is enabled, a START condition generates an interrupt to the CPU.
C controller receives a slave address match (I2CAMI = 1), loses arbitration (I2CALI = 1), or
2
C module operates in slave mode. This bit is automatically cleared whenever
2
C extended addressing mode.
2
2
C function is disabled.
C function. When set to 1, the I
2
C is operating in slave mode (I2CMST = 0) and is reset
2
C communication unit is
2
2
C module is operating as the
C abort is in progress
2
C controller while
2
C controller
2
C