ST72324BJ4-auto STMicroelectronics, ST72324BJ4-auto Datasheet - Page 81
ST72324BJ4-auto
Manufacturer Part Number
ST72324BJ4-auto
Description
8-bit MCU for automotive, 3.8 to 5.5V operating range with 16 Kbyte Flash, 10-bit ADC, 4 timers, SPI, SCI
Manufacturer
STMicroelectronics
Datasheet
1.ST72324BJ2-AUTO.pdf
(198 pages)
Specifications of ST72324BJ4-auto
Hdflash Endurance
100 cycles, data retention 20 years
Clock Sources
crystal/ceramic resonator oscillators, internal RC oscillator and external clock input
4 Power Saving Modes
Slow, Wait, Active Halt, and Halt
- Current page: 81 of 198
- Download datasheet (3Mb)
ST72324B-Auto
Output compare
In this section, the index, i, may be 1 or 2 because there are two output compare functions in
the 16-bit timer.
This function can be used to control an output waveform or indicate when a period of time
has elapsed.
When a match is found between the Output Compare register and the free running counter,
the output compare function:
●
●
●
Two 16-bit registers Output Compare register 1 (OC1R) and Output Compare register 2
(OC2R) contain the value to be compared to the counter register each timer clock cycle.
Table 45.
These registers are readable and witable and are not affected by the timer hardware. A
reset event changes the OC
Timing resolution is one count of the free running counter: (f
Procedure
To use the Output Compare function, select the following in the CR2 register:
●
●
And select the following in the CR1 register:
●
●
When a match is found between OCRi register and CR register:
●
●
●
The OC
the following formula:
Where:
t
f
PRESC = Timer prescaler factor (2, 4 or 8 depending on CC[1:0] bits; see
CPU
Assigns pins with a programmable value if the OCiE bit is set
Sets a flag in the status register
Generates an interrupt if enabled
Set the OCiE bit if an output is needed then the OCMPi pin is dedicated to the output
compare i signal.
Select the timer clock (CC[1:0]) (see
Select the OLVLi bit to applied to the OCMPi pins after the match occurs.
Set the OCIE bit to generate an interrupt if it is needed.
OCFi bit is set
The OCMPi pin takes OLVLi bit value (OCMPi pin latch is forced low during reset)
A timer interrupt is generated if the OCIE bit is set in the CR1 register and the I bit is
cleared in the CC register (CC).
i
R register value required for a specific timing application can be calculated using
= Output compare period (in seconds)
= CPU clock frequency (in hertz)
Register
Output compare byte distribution
OCiR
i
R value to 8000h.
Doc ID13466 Rev 4
OCiR =
Table
MS byte
OCiHR
t
PRESC
*
f
50).
CPU
CPU
/CC[1:0]).
On-chip peripherals
LS byte
OCiLR
Table
50)
81/198
Related parts for ST72324BJ4-auto
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search -----> STE16N100
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search ---> STE53NA50
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN Transistor Power Module
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet: