ATmega48PA Automotive Atmel Corporation, ATmega48PA Automotive Datasheet - Page 128
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATmega48PA Automotive
Manufacturer Part Number
ATmega48PA Automotive
Description
Manufacturer
Atmel Corporation
- Current page: 128 of 371
- Download datasheet (12Mb)
128
Atmel ATmega48PA/88PA/168PA [Preliminary]
The Timer/Counter Overflow Flag (TOV1) is set each time the counter reaches BOTTOM.
When either OCR1A or ICR1 is used for defining the TOP value, the OC1A or ICF1 Flag is set
accordingly at the same timer clock cycle as the OCR1x Registers are updated with the dou-
ble buffer value (at TOP). The Interrupt Flags can be used to generate an interrupt each time
the counter reaches the TOP or BOTTOM value.
When changing the TOP value the program must ensure that the new TOP value is higher or
equal to the value of all of the Compare Registers. If the TOP value is lower than any of the
Compare Registers, a compare match will never occur between the TCNT1 and the OCR1x.
Note that when using fixed TOP values, the unused bits are masked to zero when any of the
OCR1x Registers are written. As the third period shown in
TOP actively while the Timer/Counter is running in the phase correct mode can result in an
unsymmetrical output. The reason for this can be found in the time of update of the OCR1x
Register. Since the OCR1x update occurs at TOP, the PWM period starts and ends at TOP.
This implies that the length of the falling slope is determined by the previous TOP value, while
the length of the rising slope is determined by the new TOP value. When these two values dif-
fer the two slopes of the period will differ in length. The difference in length gives the
unsymmetrical result on the output.
It is recommended to use the phase and frequency correct mode instead of the phase correct
mode when changing the TOP value while the Timer/Counter is running. When using a static
TOP value there are practically no differences between the two modes of operation.
In phase correct PWM mode, the compare units allow generation of PWM waveforms on the
OC1x pins. Setting the COM1x1:0 bits to two will produce a non-inverted PWM and an
inverted PWM output can be generated by setting the COM1x1:0 to three (See
134). The actual OC1x value will only be visible on the port pin if the data direction for the port
pin is set as output (DDR_OC1x). The PWM waveform is generated by setting (or clearing) the
OC1x Register at the compare match between OCR1x and TCNT1 when the counter incre-
ments, and clearing (or setting) the OC1x Register at compare match between OCR1x and
TCNT1 when the counter decrements. The PWM frequency for the output when using phase
correct PWM can be calculated by the following equation:
The N variable represents the prescaler divider (1, 8, 64, 256, or 1024).
The extreme values for the OCR1x Register represent special cases when generating a PWM
waveform output in the phase correct PWM mode. If the OCR1x is set equal to BOTTOM the
output will be continuously low and if set equal to TOP the output will be continuously high for
non-inverted PWM mode. For inverted PWM the output will have the opposite logic values. If
OCR1A is used to define the TOP value (WGM13:0 = 11) and COM1A1:0 = 1, the OC1A out-
put will toggle with a 50% duty cycle.
f
OCnxPCPWM
=
--------------------------------- -
2
f
clk_I/O
N
TOP
Figure 16-8
illustrates, changing the
Table on page
9223B–AVR–09/11
Related parts for ATmega48PA Automotive
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ATmega48PA](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
![ATMEGA48PA-15MZ](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
ATMEL Corporation
Datasheet:
![ATMEGA48P-20MU](/photos/12/13/121314/atmega48p-20mu_tmb.jpg)
Part Number:
Description:
MCU AVR 4K ISP FLASH 20MHZ 32QFN
Manufacturer:
Atmel
Datasheet:
![ATmega48P](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
![ATMEGA48P-20AU](/photos/6/91/69154/313-32-tqfp_tmb.jpg)
Part Number:
Description:
MCU AVR 4K ISP FLSH 20MHZ 32TQFP
Manufacturer:
Atmel
Datasheet:
![ATMEGA48P-20PU](/photos/7/21/72189/453-28-dip_tmb.jpg)
Part Number:
Description:
MCU AVR 4K ISP FLASH 20MHZ 28DIP
Manufacturer:
Atmel
Datasheet:
![ATMEGA48P-20AUR](/photos/6/91/69154/313-32-tqfp_tmb.jpg)
Part Number:
Description:
MCU AVR 4K FLASH 20MHZ 32TQFP
Manufacturer:
Atmel
Datasheet:
![ATMEGA48P-20MUR](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
MCU AVR 4K FLASH 20MHZ 32QFN
Manufacturer:
Atmel
Datasheet:
![ATMEGA48P-20MMU](/photos/12/32/123209/28m1-vqfn_tmb.jpg)
Part Number:
Description:
MCU AVR 4K FLASH 20MHZ 28-QFN
Manufacturer:
Atmel
Datasheet:
![ATMEGA48P-20MMUR](/photos/12/32/123209/28m1-vqfn_tmb.jpg)
Part Number:
Description:
MCU AVR 4K FLASH 20MHZ 28QFN
Manufacturer:
Atmel
Datasheet:
![U641B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
![U4082B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet: