AT32UC3C1512C Automotive Atmel Corporation, AT32UC3C1512C Automotive Datasheet - Page 887
AT32UC3C1512C Automotive
Manufacturer Part Number
AT32UC3C1512C Automotive
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT90CAN128_AUTOMOTIVE.pdf
(225 pages)
2.AT32UC3C0512C_AUTOMOTIVE.pdf
(1312 pages)
3.AT32UC3C0512C_AUTOMOTIVE.pdf
(107 pages)
- AT90CAN128_AUTOMOTIVE PDF datasheet
- AT32UC3C0512C_AUTOMOTIVE PDF datasheet #2
- AT32UC3C0512C_AUTOMOTIVE PDF datasheet #3
- Current page: 887 of 1312
- Download datasheet (20Mb)
32.6.2.15
9166C–AVR-08/11
RXOUTI
FIFOCON
OUT
Management of OUT endpoints
• Overview
(bank 0)
DATA
set, or if the total byte count is not an integral multiple of EPSIZE, whereby the last packet
should be short.
To enable the multi packet mode, the user should configure the endpoint descriptor
(EPn_PCKSIZE_BK0/1.BYTE_COUNT) to the total size of the multi packet, which should be
larger than the endpoint size (EPSIZE).
Since the EPn_PCKSIZE_BK0/1.MULTI_PACKET_SIZE is incremented (by the transmitted
packet size) after each successful transaction, it should be set to zero when setting up a new
multi packet transfer.
The EPn_PCKSIZE_BK0/1.MULTI_PACKET_SIZE is cleared by hardware when all the bank
contents have been sent. The bank is considered as ready and the TX_IN flag is set when:
The endpoint and its descriptor in RAM must be pre configured, see section
on page 880
When the current bank is full, the RXOUTI and FIFO Control (UECONn.FIFOCON) bits will be
set simultaneously. This triggers an EPnINT interrupt if the Received OUT Data Interrupt Enable
(RXOUTE) bit in UECONn is one.
RXOUTI shall be cleared by software (by writing a one to the Received OUT Data Interrupt Clear
(RXOUTIC) bit) to acknowledge the interrupt. This has no effect on the endpoint FIFO.
The user reads the OUT data from the RAM and clears the FIFOCON bit to free the bank. This
will also cause a switch to the next bank if the OUT endpoint is composed of multiple banks.
RXOUTI should always be cleared before clearing FIFOCON to avoid missing an RXOUTI
event.
Figure 32-14. Example of an OUT endpoint with one data bank
• A short packet (smaller than EPSIZE) has been transmitted.
• A packet has been successfully transmitted, the updated MULTI_PACKET_SIZE equals the
• An extra zero length packet has been automatically sent for the last transfer of the current
BYTE_COUNT, and the AUTO_ZLP field is not set.
bank, if BYTE_COUNT is a multiple of EPSIZE and AUTO_ZLP is set.
HW
ACK
for more details.
SW
read data from CPU
BANK 0
NAK
SW
OUT
(bank 0)
DATA
HW
ACK
AT32UC3C
”RAM management”
read data from CPU
SW
BANK 0
887
Related parts for AT32UC3C1512C Automotive
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: