AT32UC3C1512C Automotive Atmel Corporation, AT32UC3C1512C Automotive Datasheet - Page 879
AT32UC3C1512C Automotive
Manufacturer Part Number
AT32UC3C1512C Automotive
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT90CAN128_AUTOMOTIVE.pdf
(225 pages)
2.AT32UC3C0512C_AUTOMOTIVE.pdf
(1312 pages)
3.AT32UC3C0512C_AUTOMOTIVE.pdf
(107 pages)
- AT90CAN128_AUTOMOTIVE PDF datasheet
- AT32UC3C0512C_AUTOMOTIVE PDF datasheet #2
- AT32UC3C0512C_AUTOMOTIVE PDF datasheet #3
- Current page: 879 of 1312
- Download datasheet (20Mb)
32.6.2.7
32.6.2.8
32.6.2.9
9166C–AVR-08/11
Suspend and Wakeup
Detach
Remote wakeup
Once the USB device address is configured, the controller filters the packets to only accept
those targeting the address stored in UADD.
UADD and ADDEN should not be written to simultaneously. They should be written sequentially,
UADD field first.
If UADD or ADDEN is cleared, the default device address 0 is used. UADD and ADDEN are
cleared:
When an idle USB bus state has been detected for 3 ms, the controller sets the Suspend
(SUSP) interrupt bit in UDINT. In this case, the transceiver is suspended, reducing power
consumption.
To further reduce power consumption it is recommended to freeze the USB clock by writing a
one to the Freeze USB Clock (FRZCLK) bit in USBCON when the USB bus is in suspend mode.
The MCU can also enter the idle or frozen sleep mode to further lower power consumption.
To recover from the suspend mode, the user shall wait for the Wakeup (WAKEUP) interrupt bit,
which is set when a non-idle event is detected, and then write a zero to FRZCLK.
As the WAKEUP interrupt bit in UDINT is set when a non-idle event is detected, it can occur
regardless of whether the controller is in the suspend mode or not. The SUSP and WAKEUP
interrupts are thus independent of each other except for that one bit is cleared when the other is
set.
The reset value of the DETACH bit located in the UDCON register, is one.
It is possible to initiate a device re-enumeration simply by writing a one and then a zero to
DETACH.
DETACH acts on the pull-up connections of the DP and DM pads. See
ther details.
The remote wakeup request (also known as upstream resume) is the only request the device
may send on its own initiative. This should be preceded by a DEVICE_REMOTE_WAKEUP
request from the host.
• After all kinds of resets, the USB device address is 0.
• The host starts a SETUP transaction with a SET_ADDRESS(addr) request.
• The user writes this address to the USB Address field (UDCON.UADD), and writes a zero to
• The user sends a zero-length IN packet from the control endpoint.
• The user enables the stored USB device address by writing a one to ADDEN.
• On a hardware reset.
• When the USBC is disabled (USBE written to zero).
• When a USB reset is detected.
• First, the USBC must have detected a “Suspend” state on the bus, i.e. the remote wakeup
the Address Enable bit (UDCON.ADDEN), resulting in the address remaining zero.
request can only be sent after a SUSP interrupt has been set.
“Device mode”
AT32UC3C
for fur-
879
Related parts for AT32UC3C1512C Automotive
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: