AT32UC3C1512C Automotive Atmel Corporation, AT32UC3C1512C Automotive Datasheet - Page 765
AT32UC3C1512C Automotive
Manufacturer Part Number
AT32UC3C1512C Automotive
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT90CAN128_AUTOMOTIVE.pdf
(225 pages)
2.AT32UC3C0512C_AUTOMOTIVE.pdf
(1312 pages)
3.AT32UC3C0512C_AUTOMOTIVE.pdf
(107 pages)
- AT90CAN128_AUTOMOTIVE PDF datasheet
- AT32UC3C0512C_AUTOMOTIVE PDF datasheet #2
- AT32UC3C0512C_AUTOMOTIVE PDF datasheet #3
- Current page: 765 of 1312
- Download datasheet (20Mb)
29.6.2.3
29.6.2.4
9166C–AVR-08/11
Overload frames
Errors and fault confinement
The channel mode is not changed when the channel is disabled, i.e. the Fault Confinement Reg-
ister (CANFC) is not cleared. Therefore, if the channel was in error passive mode before being
disabled, it stays in error passive mode when re-enabled.
Figure 29-5. Enable and Disable Sequences
The CAN protocol allows nodes to send overload frames to provide extra delay between two
messages.
User can at any time request to send overload frames by writing the Overload Request bit (CAN-
CTRL.OVRQ) to one. A single overload frame will then be sent at the end of the next message.
When transission of the overload frame starts, CANSR.OVS is set and CANCTRL.OVRQ is
cleared. At this time, user can write CANCTRL.OVRQ to one again to send a second overload
frame at the end of the first one. The CAN protocol specifies that maximum two overload frames
can be sent.
Figure 29-6. Overload Frame Request
This section refers to chapter 6 (Error handling) and chapter 7 (Fault confinement) of the CAN
Specification.
There are 5 different error types which are not mutually exclusive. Error status can be read in the
Interrupt Status Register (CANISR). Error status bits are set by hardware and can only be
cleared by user.
When the channel enters bus off state, the Bus Off Status bit (CANISR.BOFF) is set. In this
state the channel can no longer communicate on the bus. The channel can leave bus off state if
it detects 128 occurrences of 11 consecutive recessive bits on the bus.
The Last Selected MOb Status field (CANISR.LSMOB) identifies the MOb that was selected
when the error occurred. For some error types, a MOb has not been selected yet when the error
occurs. In this case, CANISR.LSMOB returns NONE.
CANCTRL.OVRQ
CANSR.OVS
CAN bus
user write
data or remote frame
CANCTRL.CEN
CANSR.CES
CAN bus
enable request
(user write)
user write
data frame
overload frame 1
bus idle
overload frame 2
disable request
data frame
(user write)
data or remote frame
AT32UC3C
765
Related parts for AT32UC3C1512C Automotive
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: