SAM9G15 Atmel Corporation, SAM9G15 Datasheet - Page 675

• Manufacturer Part Number: SAM9G15
• Manufacturer: Atmel Corporation

Specifications of SAM9G15

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 400 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 105
• Ext Interrupts: 105
• Usb Transceiver: 3
• Usb Speed: Hi-Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 3
• Uart: 6
• Lin: 4
• Ssc: 1
• Sd / Emmc: 2
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 12
• Adc Resolution (bits): 10
• Adc Speed (ksps): 440
• Resistive Touch Screen: Yes
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: DDR2/LPDDR, SDRAM/LPSDR
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 0.9 to 1.1
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

Figure 35-10. Peripheral Deselection
35.7.3.10
11052C–ATARM–21-Nov-11
Write SPI_TDR
Write SPI_TDR
Write SPI_TDR
NPCS[0..3]
NPCS[0..3]
NPCS[0..3]
TDRE
TDRE
TDRE
Mode Fault Detection
A
A
A
nected to other peripherals are in use as well, the SPI DMAC might be delayed by another
(DMAC with a higher priority on the bus). Having DMAC buffers in slower memories like flash
memory or SDRAM compared to fast internal SRAM, may lengthen the reload time of the
SPI_TDR by the DMAC as well. This means that the SPI_TDR might not be reloaded in time to
keep the chip select line low. In this case the chip select line may toggle between data transfer
and according to some SPI Slave devices, the communication might get lost. The use of the
CSAAT bit might be needed.
Figure 35-10
A mode fault is detected when the SPI is programmed in Master Mode and a low level is driven
by an external master on the NPCS0/NSS signal. In this case, multi-master configuration,
NPCS0, MOSI, MISO and SPCK pins must be configured in open drain (through the PIO control-
ler). When a mode fault is detected, the MODF bit in the SPI_SR is set until the SPI_SR is read
and the SPI is automatically disabled until re-enabled by writing the SPIEN bit in the SPI_CR
(Control Register) at 1.
DLYBCT
DLYBCT
DLYBCT
CSAAT = 0
DLYBCS
DLYBCS
DLYBCS
PCS = B
PCS=A
shows different peripheral deselction cases and the effect of the CSAAT bit.
PCS = A
A
B
A
A
A
A
DLYBCT
DLYBCT
DLYBCT
CSAAT = 1
DLYBCS
DLYBCS
PCS = B
PCS = A
A
A
PCS = A
DLYBCS
SAM9G15
A
A
B
675