ATtiny48 Atmel Corporation, ATtiny48 Datasheet - Page 162

• Manufacturer Part Number: ATtiny48
• Manufacturer: Atmel Corporation

Specifications of ATtiny48

• Flash (kbytes): 4 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 12 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 28
• Ext Interrupts: 28
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.25
• Eeprom (bytes): 64
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 2
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

16.2
16.2.1
16.2.2
162
Register Description
ATtiny48/88
ADCSRB – ADC Control and Status Register B
ACSR – Analog Comparator Control and Status Register
Table 16-1.
• Bit 6 – ACME: Analog Comparator Multiplexer Enable
When this bit is written logic one and the ADC is switched off (ADEN in ADCSRA is zero), the
ADC multiplexer selects the negative input to the Analog Comparator. When this bit is written
logic zero, AIN1 is applied to the negative input of the Analog Comparator. For a detailed
description of this bit, see
• Bit 7 – ACD: Analog Comparator Disable
When this bit is written logic one, the power to the Analog Comparator is switched off. This bit
can be set at any time to turn off the Analog Comparator. This will reduce power consumption in
Active and Idle mode. When changing the ACD bit, the Analog Comparator Interrupt must be
disabled by clearing the ACIE bit in ACSR. Otherwise an interrupt can occur when the bit is
changed.
• Bit 6 – ACBG: Analog Comparator Bandgap Select
When this bit is set, a fixed internal bandgap reference voltage replaces the positive input to the
Analog Comparator. When this bit is cleared, AIN0 is applied to the positive input of the Analog
Comparator.
• Bit 5 – ACO: Analog Comparator Output
The output of the Analog Comparator is synchronized and then directly connected to ACO. The
synchronization introduces a delay of 1 – 2 clock cycles.
Bit
(0x7B)
Read/Write
Initial Value
Bit
0x30 (0x50)
Read/Write
Initial Value
ACME
1
1
1
1
1
1
See “Internal Voltage Reference” on page 45.
Analog Comparator Multiplexed Input (Continued)
ACD
R/W
ADEN
R
7
0
7
–
0
0
0
0
0
0
0
ACBG
ACME
R/W
R/W
“Analog Comparator Multiplexed Input” on page
6
0
6
0
MUX[2:0]
010
011
100
101
110
111
ACO
N/A
R
5
R
5
–
0
Analog Comparator Negative Input
ADC2
ADC3
ADC4
ADC5
ADC6
ADC7
R/W
ACI
R
4
0
4
–
0
ACIE
R/W
3
0
R
3
–
0
ADTS2
ACIC
R/W
R/W
2
0
2
0
ADTS1
ACIS1
R/W
R/W
1
0
1
0
161.
ADTS0
ACIS0
R/W
R/W
0
0
0
0
8008H–AVR–04/11
ADCSRB
ACSR