AT32UC3B0512AU Atmel Corporation, AT32UC3B0512AU Datasheet - Page 605

• Manufacturer Part Number: AT32UC3B0512AU
• Manufacturer: Atmel Corporation

Specifications of AT32UC3B0512AU

• Flash (kbytes): 512 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 60 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 44
• Ext Interrupts: 44
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 4
• Twi (i2c): 1
• Uart: 3
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 96
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

27.6
27.6.1
27.6.1.1
27.6.2
32059L–AVR32–01/2012
JTAG Data Registers
Device Identification Register
Reset register
Device specific ID codes
The following device specific registers can be selected as JTAG scan chain depending on the
instruction loaded in the JTAG Instruction Register. Additional registers exist, but are implicitly
described in the functional description of the relevant instructions.
The Device Identification Register contains a unique identifier for each product. The register is
selected by the IDCODE instruction, which is the default instruction after a JTAG reset.
The different device configurations have different JTAG ID codes, as shown in
Note that if the flash controller is statically reset, the ID code will be undefined
Table 27-27. Device and JTAG ID
The reset register is selected by the AVR_RESET instruction and contains one bit for each reset
domain in the device. Setting each bit to one will keep that domain reset until the bit is cleared.
Bit
Device ID
Bit
Device ID
Revision
Part Number
Manufacturer ID
Device name
AT32UC3B0512
AT32UC3B1512
AT32UC3B0256
AT32UC3B1256
AT32UC3B0128
AT32UC3B1128
AT32UC3B064
AT32UC3B164
31
MSB
Revision
4 bits
OCD
4
This is a 4 bit number identifying the revision of the component.
Rev A = 0x0, B = 0x1, etc.
The part number is a 16 bit code identifying the component.
The Manufacturer ID is a 11 bit code identifying the manufacturer.
The JTAG manufacturer ID for ATMEL is 0x01F.
JTAG ID code (r is the revision number)
0xr205003F
0xr205203F
0xr1EE403F
0xr1EE503F
0xr1EE603F
0xr1EE903F
0xr1EEA03F
0xr1EEB03F
28
27
Part Number
16 bits
APP
3
12
RESERVED
11
2
Manufacturer ID
11 bits
RESERVED
1
.
1
Table
CPU
LSB
0
LSB
1 bit
27-27.
0
1
605