AT32UC3B0512AU Atmel Corporation, AT32UC3B0512AU Datasheet - Page 307

• Manufacturer Part Number: AT32UC3B0512AU
• Manufacturer: Atmel Corporation

Specifications of AT32UC3B0512AU

• Flash (kbytes): 512 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 60 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 44
• Ext Interrupts: 44
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 4
• Twi (i2c): 1
• Uart: 3
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 96
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

21.6.4.3
32059L–AVR32–01/2012
Asynchronous Receiver
Figure 21-9. Start Frame Delimiter
Manchester Drift Compensation
The Drift compensation bit (MAN.DRIFT) enables a hardware drift compensation and recovery
system that allows for sub-optimal clock drifts without further user intervention. Drift compensa-
tion is only available in 16x oversampling mode. If the RXD event is one 16
the expected edge, it is considered as normal jitter and no corrective action will be taken. If the
event is two to four 16
to three 16
Figure 21-10. Bit Resynchronization
If the USART is configured in an asynchronous operating mode (MR.SYNC = 0), the receiver will
oversample the RXD input line by either 8 or 16 times the baud rate clock, as selected by the
Oversampling Mode bit (MR.OVER). If the line is zero for half a bit period (four or eight consecu-
tive samples, respectively), a start bit will be assumed, and the following 8th or 16th sample will
determine the logical value on the line, in effect resulting in bit values being determined at the
middle of the bit period.
The number of data bits, endianess, parity mode, and stop bits are selected by the same bits
and fields as for the transmitter (MR.CHRL, MODE9, MSBF, PAR, and NBSTOP). The synchro-
Oversampling
Sampling
16x Clock
th
point
RXD
’s after the expected edge, the current period will be prolonged by a 16
Manchester
Manchester
Manchester
encoded
encoded
encoded
th
data
data
data
’s early, the current period will be shortened by a 16
Preamble Length
Synchro.
Txd
Txd
Txd
Error
is set to 0
Synchro.
SFD
SFD
SFD
Jump
DATA
One bit start frame delimiter
Expected edge
Tolerance
start frame delimiter
start frame delimiter
DATA
DATA
Command Sync
Jump
Sync
Data Sync
Synchro.
th
th
. If the event is two
Error
clock cycle from
th
.
307