AT32UC3B0512AU Atmel Corporation, AT32UC3B0512AU Datasheet - Page 414

• Manufacturer Part Number: AT32UC3B0512AU
• Manufacturer: Atmel Corporation

Specifications of AT32UC3B0512AU

• Flash (kbytes): 512 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 60 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 44
• Ext Interrupts: 44
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 4
• Twi (i2c): 1
• Uart: 3
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 96
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

22.8.2
22.8.2.1
Register Name:
Access Type:
Offset:
Reset Value:
• LS: Low-Speed Mode Force
• RMWKUP: Remote Wake-Up
• DETACH: Detach
• ADDEN: Address Enable
• UADD: USB Address
32059L–AVR32–01/2012
ADDEN
31
23
15
7
-
-
-
1: The low-speed mode is active.
0: The full-speed mode is active.
This bit can be written even if USBE is zero or FRZCLK is one. Disabling the USBB (by writing a zero to the USBE bit) does not
reset this bit.
Writing a one to this bit will send an upstream resume to the host for a remote wake-up.
Writing a zero to this bit has no effect.
This bit is cleared when the USBB receive a USB reset or once the upstream resume has been sent.
Writing a one to this bit will physically detach the device (disconnect internal pull-up resistor from D+ and D-).
Writing a zero to this bit will reconnect the device.
Writing a one to this bit will activate the UADD field (USB address).
Writing a zero to this bit has no effect.
This bit is cleared when a USB reset is received.
This field contains the device address.
This field is cleared when a USB reset is received.
USB Device Registers
Device General Control Register
30
22
14
6
-
-
-
UDCON
Read/Write
0x0000
0x00000100
29
21
13
5
-
-
-
LS
28
20
12
4
-
-
UADD
27
19
11
3
-
-
-
26
18
10
2
-
-
-
RMWKUP
25
17
9
1
-
-
DETACH
24
16
8
0
-
-
414