PIC18F4550-I/P Microchip Technology Inc., PIC18F4550-I/P Datasheet - Page 260

• Manufacturer Part Number: PIC18F4550-I/P
• Description: 40 PIN, 32 KB FLASH, 2048 RAM, FS-USB 2.0
• Manufacturer: Microchip Technology Inc.

Specifications of PIC18F4550-I/P

• A/d Inputs: 13-Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 12 MIPS
• Eeprom Memory: 256 Bytes
• Input Output: 34
• Interface: I2C/SPI/UART/USART/USB
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 40-pin PDIP
• Programmable Memory: 32K Bytes
• Ram Size: 2K Bytes
• Speed: 48 MHz
• Timers: 1-8-bit, 3-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

PIC18F2455/2550/4455/4550
20.4.2
The operation of the Synchronous Master and Slave
modes is identical, except in the case of Sleep, or any
Idle mode and bit SREN, which is a “don’t care” in
Slave mode.
If receive is enabled by setting the CREN bit prior to
entering Sleep or any Idle mode, then a word may be
received while in this low-power mode. Once the word
is received, the RSR register will transfer the data to the
RCREG register. If the RCIE enable bit is set, the
interrupt generated will wake the chip from the low-
power mode. If the global interrupt is enabled, the
program will branch to the interrupt vector.
TABLE 20-10: REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE RECEPTION
DS39632C-page 258
INTCON
PIR1
PIE1
IPR1
RCSTA
RCREG
TXSTA
BAUDCON
SPBRGH
SPBRG
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for synchronous slave reception.
Note 1:
Name
Reserved in 28-pin devices; always maintain these bits clear.
EUSART SYNCHRONOUS SLAVE
RECEPTION
EUSART Receive Register
EUSART Baud Rate Generator Register High Byte
EUSART Baud Rate Generator Register Low Byte
GIE/GIEH PEIE/GIEL TMR0IE
ABDOVF
SPPIE
SPPIP
SPPIF
CSRC
SPEN
Bit 7
(1)
(1)
(1)
RCIDL
ADIF
ADIE
ADIP
Bit 6
RX9
TX9
RXDTP
SREN
TXEN
RCIE
RCIP
RCIF
Bit 5
Preliminary
TXCKP
INT0IE
CREN
SYNC
TXIE
TXIP
Bit 4
TXIF
ADDEN
SENDB
BRG16
SSPIE
SSPIP
To set up a Synchronous Slave Reception:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. If using interrupts, ensure that the GIE and PEIE
SSPIF
RBIE
Bit 3
Enable the synchronous master serial port by
setting bits SYNC and SPEN and clearing bit
CSRC.
If interrupts are desired, set enable bit RCIE.
If the signal from the CK pin is to be inverted, set
the TXCKP bit. If the signal from the DT pin is to
be inverted, set the RXDTP bit.
If 9-bit reception is desired, set bit RX9.
To enable reception, set enable bit CREN.
Flag bit, RCIF, will be set when reception is
complete. An interrupt will be generated if
enable bit, RCIE, was set.
Read the RCSTA register to get the 9th bit (if
enabled) and determine if any error occurred
during reception.
Read the 8-bit received data by reading the
RCREG register.
If any error occurred, clear the error by clearing
bit CREN.
bits in the INTCON register (INTCON<7:6>) are
set.
TMR0IF
CCP1IE
CCP1IP
CCP1IF
BRGH
FERR
Bit 2
—
TMR2IF
TMR2IE
TMR2IP
INT0IF
OERR
TRMT
WUE
© 2006 Microchip Technology Inc.
Bit 1
TMR1IF
TMR1IE
TMR1IP
ABDEN
RX9D
TX9D
RBIF
Bit 0
on page
Values
Reset
51
54
54
54
53
53
53
53
53
53