LAN9311-NU SMSC, LAN9311-NU Datasheet - Page 173

• Manufacturer Part Number: LAN9311-NU
• Description: IC ETHER SW 2PRT 16BIT 128-VTQFP
• Manufacturer: SMSC
• Type: Two Port Managed Ethernet Switchr

Specifications of LAN9311-NU

• Controller Type: Ethernet Switch Controller
• Interface: Serial EEPROM
• Voltage - Supply: 3.3V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 128-TQFP, 128-VQFP
• Product: Ethernet Switches
• Number Of Transceivers: 1
• Standard Supported: 802.3, 802.3u
• Data Rate: 10 MB, 100 MB
• Supply Voltage (max): 3.3 V
• Supply Voltage (min): 0 V
• Maximum Operating Temperature: + 70 C
• Ethernet Connection Type: 10 Base-T, 100 Base-TX
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• For Use With: 638-1076 - EVALUATION BOARD LAN9311-NU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Supply: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 638-1075

Two Port 10/100 Managed Ethernet Switch with 16-Bit Non-PCI CPU Interface
Datasheet
SMSC LAN9311/LAN9311i
14.2.1
14.2.1.1
31:24
23:15
BITS
11:9
7:5
14
13
12
8
Interrupt De-assertion Interval (INT_DEAS)
This field determines the Interrupt Request De-assertion Interval in multiples
of 10 microseconds.
Setting this field to zero causes the device to disable the INT_DEAS Interval,
reset the interval counter and issue any pending interrupts. If a new, non-
zero value is written to this field, any subsequent interrupts will obey the new
setting.
This field does not apply to the PME_INT interrupt.
RESERVED
Interrupt De-assertion Interval Clear (INT_DEAS_CLR)
Writing a 1 to this register clears the de-assertion counter in the Interrupt
Controller, thus causing a new de-assertion interval to begin (regardless of
whether or not the Interrupt Controller is currently in an active de-assertion
interval).
0: Normal operation
1: Clear de-assertion counter
Interrupt De-assertion Status (INT_DEAS_STS)
When set, this bit indicates that interrupts are currently in a de-assertion
interval, and will not be sent to the IRQ pin. When this bit is clear, interrupts
are not currently in a de-assertion interval, and will be sent to the IRQ pin.
0: No interrupts in de-assertion interval
1: Interrupts in de-assertion interval
Master Interrupt (IRQ_INT)
This read-only bit indicates the state of the internal IRQ line, regardless of
the setting of the IRQ_EN bit, or the state of the interrupt de-assertion
function. When this bit is set, one of the enabled interrupts is currently
active.
0: No enabled interrupts active
1: One or more enabled interrupts active
RESERVED
IRQ Enable (IRQ_EN)
This bit controls the final interrupt output to the IRQ pin. When clear, the IRQ
output is disabled and permanently de-asserted. This bit has no effect on
any internal interrupt status bits.
0: Disable output on IRQ pin
1: Enable output on IRQ pin
RESERVED
Interrupts
This section details the interrupt related System CSR’s. These registers control, configure, and monitor
the IRQ interrupt output pin and the various LAN9311/LAN9311i interrupt sources. For more
information on the LAN9311/LAN9311i interrupts, refer to
Interrupt Configuration Register (IRQ_CFG)
This read/write register configures and indicates the state of the IRQ signal.
Offset:
054h
DESCRIPTION
DATASHEET
173
Size:
Chapter 5, "System Interrupts," on page
32 bits
TYPE
R/W
R/W
R/W
RO
RO
RO
RO
RO
SC
SC
Revision 1.7 (06-29-10)
DEFAULT
00h
0h
0b
0b
0b
-
-
-
49.