LAN9311-NU SMSC, LAN9311-NU Datasheet - Page 163

• Manufacturer Part Number: LAN9311-NU
• Description: IC ETHER SW 2PRT 16BIT 128-VTQFP
• Manufacturer: SMSC
• Type: Two Port Managed Ethernet Switchr

Specifications of LAN9311-NU

• Controller Type: Ethernet Switch Controller
• Interface: Serial EEPROM
• Voltage - Supply: 3.3V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 128-TQFP, 128-VQFP
• Product: Ethernet Switches
• Number Of Transceivers: 1
• Standard Supported: 802.3, 802.3u
• Data Rate: 10 MB, 100 MB
• Supply Voltage (max): 3.3 V
• Supply Voltage (min): 0 V
• Maximum Operating Temperature: + 70 C
• Ethernet Connection Type: 10 Base-T, 100 Base-TX
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• For Use With: 638-1076 - EVALUATION BOARD LAN9311-NU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Supply: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 638-1075

Two Port 10/100 Managed Ethernet Switch with 16-Bit Non-PCI CPU Interface
Datasheet
Chapter 13 GPIO/LED Controller
SMSC LAN9311/LAN9311i
13.1
13.2
The GPIO/LED Controller provides 12 configurable general purpose input/output pins, GPIO[11:0].
These pins can be individually configured to function as inputs, push-pull outputs, or open drain outputs
and each is capable of interrupt generation with configurable polarity. Two of the GPIO pins (GPIO[9:8])
can be used for IEEE 1588 timestamp functions, allowing GPIO driven 1588 time clock capture when
configured as an input, or GPIO output generation based on an IEEE 1588 clock target compare event.
In addition, 8 of the GPIO pins can be alternatively configured as LED outputs. These pins, GPIO[7:0]
(nP1LED[3:0] and nP2LED[3:0]), may be enabled to drive Ethernet status LEDs for external indication
of various attributes of the switch ports.
GPIO and LED functionality is configured via the GPIO/LED System Control and Status Registers
(CSRs), accessible through the Host Bus Interface (HBI). These registers are defined in
14.2.3, "GPIO/LED," on page
The GPIO controller is comprised of 12 programmable input/output pins. These pins are individually
configurable via the GPIO CSRs. On application of a chip-level reset:
Note: GPIO[7:0] may be configured as LED outputs by default, dependant on the LED_en_stap[7:0]
The direction and buffer type of all 12 GPIOs are configured via the
Register (GPIO_CFG)
direction of each GPIO, input or output, should be configured first via its respective GPIO direction bit
(GPDIR[11:0]) in the
configured as an output, the output buffer type for each GPIO is selected by the GPIOBUF[11:0] bits
in the
buffers are supported for each GPIO. When functioning as an open-drain driver, the GPIO output pin
is driven low when the corresponding data register bit (GPIOD in the
Direction Register
When a GPIO is enabled as an output, the value output to the GPIO pin is set via the corresponding
GPIOD[11:0] bit in the
configured as inputs, the corresponding GPIOD[11:0] bit reflects the current state of the GPIO input.
Note: For GPIO[9:8], the pin direction is a function of both the GPDIR[9:8] bits of the
Functional Overview
GPIO Operation
All GPIOs are set as inputs (GPDIR[11:0] cleared in
(GPIO_DATA_DIR))
All GPIO interrupts are disabled (GPIO[11:0]_INT_EN cleared in
Status and Enable Register (GPIO_INT_STS_EN)
All GPIO interrupts are configured to low logic level triggering (GPIO_INT_POL[11:0] cleared in
General Purpose I/O Configuration Register
General Purpose I/O Configuration Register
configuration straps. Refer to
Purpose I/O Data & Direction Register (GPIO_DATA_DIR)
the
General Purpose I/O Configuration Register
(GPIO_DATA_DIR)) is cleared to 0, and is not driven when set to 1.
General Purpose I/O Data & Direction Register
General Purpose I/O Data & Direction Register
and
General Purpose I/O Data & Direction Register
193.
DATASHEET
Section 13.3, "LED Operation"
163
(GPIO_CFG))
(GPIO_CFG). Push/pull and open-drain output
General Purpose I/O Data & Direction Register
(GPIO_CFG).
and the 1588_GPIO_OE[9:8] bits in
General Purpose I/O Configuration
General Purpose I/O Interrupt
for additional information.
(GPIO_DATA_DIR). For GPIOs
General Purpose I/O Data &
(GPIO_DATA_DIR). When
(GPIO_DATA_DIR). The
Revision 1.7 (06-29-10)
General
Section