EP3C5M164C7N Altera, EP3C5M164C7N Datasheet - Page 182

• Manufacturer Part Number: EP3C5M164C7N
• Description: IC CYCLONE III FPGA 5K 164 MBGA
• Manufacturer: Altera
• Series: Cyclone® IIIr

Specifications of EP3C5M164C7N

• Number Of Logic Elements/cells: 5136
• Number Of Labs/clbs: 321
• Total Ram Bits: 423936
• Number Of I /o: 106
• Voltage - Supply: 1.15 V ~ 1.25 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 164-MBGA
• Family Name: Cyclone III
• Number Of Logic Blocks/elements: 5136
• # I/os (max): 106
• Frequency (max): 437.5MHz
• Process Technology: 65nm
• Operating Supply Voltage (typ): 1.2V
• Logic Cells: 5136
• Ram Bits: 423936
• Operating Supply Voltage (min): 1.15V
• Operating Supply Voltage (max): 1.25V
• Operating Temp Range: 0C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 164
• Package Type: MBGA
• For Use With: 544-2601 - KIT DEV CYCLONE III LS EP3CLS200544-2411 - KIT DEV NIOS II CYCLONE III ED.
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Gates: -
• Lead Free Status / Rohs Status: Compliant
• Other names: 544-2559

9–22
Figure 9–7. In-System Programming of Serial Configuration Devices
Notes to
(1) Connect these pull-up resistors to the V
(2) The nCEO pin is left unconnected or used as a user I/O pin when it does not feed the nCE pin of another device.
(3) Power up the V
(4) The MSEL pin settings vary for different configuration voltage standards and POR time. To connect MSEL[3..0], refer to
(5) These are dual-purpose I/O pins. This nCSO pin functions as the FLASH_NCE pin in AP mode. The ASDO pin functions as the DATA[1] pin in
(6) The diodes and capacitors must be placed as close as possible to the Cyclone III device family. Ensure that the diodes and capacitors maintain a
(7) When cascading Cyclone III device family in a multi-device AS configuration, connect the repeater buffers between the master and slave devices
Cyclone III Device Handbook, Volume 1
page
other AP and FPP modes.
maximum AC voltage of 4.1 V. The external diodes and capacitors are required to prevent damage to the Cyclone III device family AS configuration
input pins due to possible overshoot when programming the serial configuration device using a download cable. For effective voltage clamping,
Altera recommends using the Schottky diode, which has a relatively lower forward diode voltage (VF) than the switching and Zener diodes. For
more information about the interface guidelines using Schottky diodes, refer to
Devices.
for DATA[0] and DCLK. All I/O inputs must maintain a maximum AC voltage of 4.1 V. The output resistance of the repeater buffers must fit the
maximum overshoot equation outlined in
Figure
9–11. Connect the MSEL pins directly to V
9–7:
CC
of the ByteBlaster II or USB-Blaster download cable with the 3.3-V supply.
Configuration Device
Figure 9–7
Serial
Chapter 9: Configuration, Design Security, and Remote System Upgrades in the Cyclone III Device Family
DCLK
DATA
ASDI
nCS
10
shows the download cable connections to the serial configuration device.
CCIO
V CCIO (1)
kΩ
“Configuration and JTAG Pin I/O Requirements” on page 9–7.
supply of the bank in which the pin resides.
10
kΩ
CCA
GND
10
or ground.
V CCIO (1)
(6)
kΩ
10 pf
(6)
3.3 V
GND
GND
3.3 V
10
10 pf
V CCIO (1)
kΩ
10 pf
GND
3.3 V
3.3 V
GND
10 pf
AN 523: Cyclone III Configuration Interface Guidelines with EPCS
ByteBlaster II or USB Blaster
nSTATUS
CONF_DONE
nCONFIG
nCE
DATA[0] (7)
DCLK (7)
nCSO (5)
ASDO (5)
Pin 1
10-Pin Male Header
Cyclone III Device Family
3.3 V (3)
GND
GND
MSEL[3..0]
© December 2009 Altera Corporation
nCEO
N.C. (2)
(4)
Configuration Features
Table 9–7 on