WJLXT385LE.B1 Cortina Systems Inc, WJLXT385LE.B1 Datasheet - Page 44
WJLXT385LE.B1
Manufacturer Part Number
WJLXT385LE.B1
Description
Manufacturer
Cortina Systems Inc
Datasheet
1.WJLXT385LE.B1.pdf
(138 pages)
Specifications of WJLXT385LE.B1
Lead Free Status / RoHS Status
Supplier Unconfirmed
- Current page: 44 of 138
- Download datasheet (2Mb)
44
Intel
Table 11. Clocks and Clock-Related Signals (Sheet 2 of 2)
®
LXT385 Octal E1 S/H PCM Transceiver with JA
MCLK
RCLK
SCLK
TCLK
1. DI: Digital Input
Signal
Name
QFP
Pin
10
PBGA
Ball
E1
Signal
Type
DI
Master Clock Input.
MCLK is an independent, free-running reference clock that must be
used at 2.048 MHz, to generate the following internal reference
signals:
If MCLK is:
NOTE:
Caution: Whenever MCLK is not provided, the LXT385 ransceiver is
Receive Clock Output 7:0.
For information on RCLK, see
Shift Clock Input.
For information on SCLK, see
Bus and Interface
Transmit Clock Input 7:0.
For information on TCLK, see
• Reference clock during a blue-alarm transmit-all-ones condition.
• Generation of RCLK signal during a loss-of-signal condition.
• Timing reference for the integrated clock-recovery unit, and the
• Wait-state generation logic for host processors that use parallel
• Low continuously, the complete receive path is powered down and
• High continuously, the phase-locked loop clock-recovery circuit is
• MCLK is not required if the LXT385 ransceiver is used as an
• The TAOS generator uses MCLK as a timing reference. To ensure
• If MCLK is not provided, the LXT385 ransceiver cannot be used
integrated digital jitter attenuator.
interfaces.
output pins RCLK, RPOS, and RNEG are switched to a high-
impedance tristate.
disabled and the LXT385 ransceiver operates as only a simple
data receiver (without clock recovery).
analog front end without clock recovery and jitter attenuation.
the output frequency is within specification limits, MCLK must
have the applicable stability.
for data recovery with Motorola processors because wait states
cannot be added. (Wait-state generation through ACK is not
available.)
forced into a static state, possibly causing the TTIP/TRING
outputs to overheat. To prevent overheating, see
6.5, “Line-Interface
Signals”.
Signal Description
Protection”.
Section 5.3, “Framer/Mapper
Section 5.2, “Microprocessor-Standard
Section 5.3, “Framer/Mapper
Revision Date: 19-Jan-2006
Document Number: 249252
Revision Number: 006
Section
Signals”.
Signals”.
Related parts for WJLXT385LE.B1
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Cortina Systems Inc
Datasheet:
Part Number:
Description:
Manufacturer:
Cortina Systems Inc
Datasheet:
Part Number:
Description:
Manufacturer:
Cortina Systems Inc
Datasheet:
Part Number:
Description:
Manufacturer:
Cortina Systems Inc
Datasheet:
Part Number:
Description:
Manufacturer:
Cortina Systems Inc
Datasheet:
Part Number:
Description:
IC ETH MAC SPI3 4-PORT 552-FCBGA
Manufacturer:
Cortina Systems Inc
Datasheet:
Part Number:
Description:
IC ETH MAC SPI3 4PORT 552-BGA
Manufacturer:
Cortina Systems Inc
Datasheet:
Part Number:
Description:
IC ETHERNET MAC 10PORT 552-CBGA
Manufacturer:
Cortina Systems Inc
Datasheet:
Part Number:
Description:
IC ETHERNET MAC 10-PORT 552-BGA
Manufacturer:
Cortina Systems Inc
Datasheet:
Part Number:
Description:
IC ETH MAC 12-PORT 1152-UPBGA
Manufacturer:
Cortina Systems Inc
Datasheet:
Part Number:
Description:
IC ETH MAC 24-PORT COMM 672-BGA
Manufacturer:
Cortina Systems Inc
Datasheet:
Part Number:
Description:
IC ETH MAC 24-PORT 1152-UPBGA
Manufacturer:
Cortina Systems Inc
Datasheet:
Part Number:
Description:
IC ETH AGGREGATOR 4P 1024-BGA
Manufacturer:
Cortina Systems Inc
Datasheet:
Part Number:
Description:
IC ETH AGGREGATOR 4PORT 1024-BGA
Manufacturer:
Cortina Systems Inc
Datasheet:
Part Number:
Description:
IC ETH AGGREGATOR 4P 1369-BGA
Manufacturer:
Cortina Systems Inc
Datasheet: